Models > CRT52 > Instructions

CRT52 Husqvarna - Instructions

All Instructions for the CRT52
1 - 7 of 7
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side.
Parts Used:
Ring Klip Number T5304-75 Cap Axle Black 1 50 x 1 00
  • Anthony from OLIVEHILL, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
12 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spring on clutch cable broke
Remove L. wheel.
Remove guard shield.
Remove old cable.
Install new cable.
Adjust throw on cable.
Put all parts back and test
Parts Used:
Cable, Clutch
  • David from SKANDIA, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Wrench set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Deflector replacement
Removed pin and spring replaced old deflector with new deflector reinsert pin and spring
Parts Used:
Deflector Assy
  • Dennis from Marianna, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original shield was damaged
Removed original shield ( 2 bolts), replaced with new shield.
Parts Used:
Shield
  • Wayne from LAKEVILLE, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Wrench set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken weld on right axle
Removed wheel (used strong magnet to catch the keeper)
Removed axle assembly from its mounting tube
(used strong magnet again to prevent keeper lose)
Installed replacement axle (again with the magnet)
Lubricated with 90 SAE
Re-installed the wheel (used magnet again to hold the keeper.
Mowed the lawn.
Parts Used:
Spindle Asm.-RH
  • walter from EDINBURG, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replaced old belt
took cover off and replace belt
Parts Used:
Belt, V
  • David from WINSTON SALEM, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Socket set, Wrench set
4 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front wheels, too much end play
Shimmed the wheels out on axle.. No more slop.
Parts Used:
Washer 25/32 x 1-1/4 x 16 Ga.
  • Frederick from BINGHAMTON, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
7 of 28 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CRT52
1 - 7 of 7
Back to Top