CRT215HPW0 Crosley Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
grandkids had broken the top and middle shelf bins in my refrigerator door
I simply snapped the proper pieces in place. It was sooo easy!
Parts Used:
-
Connie from Franklin, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
588 of 612 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the shelf broke
-
iris from talahassee, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
467 of 472 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door shelves were broken through uses.
There were no screws to remove or add. All were snap on parts.
Parts Used:
-
ANDRE from GERMANTOWN, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
398 of 408 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Shelving Groove Breaks
It was so easy! I just slipped the shelving units in to the groove of the refrigerator, and it took approximately 2 minutes. I am so glad that I came across this company, because for the last 3 years I have tried to fix the shelving.
Parts Used:
-
Erica from Harvey, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
377 of 382 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator would not run but interior light was on.
I unplugged the refrigerator, then opened the door and removed four screws holding the plastic electrical panel to the interior top of the main refrigerator compartment and noticed the cold control was corroded badly, apparently from moisture in the panel. I ordered a new one from partselect.com. When it arrived the next day, I then pulled off the control knob, unclipped the cold control, unplugged the three wires to the control, then removed the styrofoam insulation blocks holding the thermocouple wire and then removed the thermocouple wire to complete the removal. I then reversed the process to install the new thermostat and control. That is repositioned the thermocouple wire, put the insulation blocks back to hold the wire, then replugged the three electrical wires, clipped the control back and pushed the control knob back on and finally screwed the panel back to the top of the main compartment and plugged the refrigerator electrical cord back in to provide current to the refrigerator. It immediately started up and ran fine. Total time - about 8 minutes.
Parts Used:
-
Bruce from Alton, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
179 of 232 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light socket melted around bulb
After unsuccessfully trying to change the blown light bulb I discovered that the plastic light socket had gotten so hot that it melted and permanently fused with the blown bulb. After my new socket arrived in the mail I just popped the temp control assembly out with a screw driver and removed the old socket and placed the new one in. Whole operation to 5 minutes.
Parts Used:
-
William from Alexandria, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
65 of 107 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door shelf/bin broke and fell off
I simply snapped in the new part. It took a few seconds. I would like to say that I found the part using the model number of the fridge. When I went to look at the description it said the part was 26 inches. The one I had was only 24 3/4 inches. I called you guys and was told that this was the correct part and to ignore the measuement.
You were Right! the part fitted perfectly.
You were Right! the part fitted perfectly.
Parts Used:
-
Phillip from Cary, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
45 of 50 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic frame broken
Lifted out old part, removed glass shelf and slid it into position in new frame. Reploaced the frame in refridgerator. Slid plastic storage bins into place. Job Done.
Parts Used:
-
James from Owego, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
32 of 38 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken door shelf
Remove the broken piece by tilting upward and then sliding straight out.
Simply replace with the new door shelf by aligning the small hooks with the slots on the door. Tilt the shelf up, insert the hooks into the slots and then tilt the shelf back down to its normal postion. It is now locked in place and you are done!
Simply replace with the new door shelf by aligning the small hooks with the slots on the door. Tilt the shelf up, insert the hooks into the slots and then tilt the shelf back down to its normal postion. It is now locked in place and you are done!
Parts Used:
-
Michael from Fort Lauderdale, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
22 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator light was out
Test the light socket first with a bulb that you know is good. If the light still does not come on, unplug the refrigerator, remove the switch by inserting a very small, thin, flathead screwdriver alongside it and pull the switch out slowly with your other hand. There are two wires there. Remove them gently with some needle nose pliers. If you want to test to see if the switch is defective, take a insulated jumper wire, and attach it between the two wires. Plug the refrigerator back in and see if the light comes on. If the light does come on, replace with a new switch by re-attaching the wires and placing it back in the hole firmly.
Parts Used:
-
andy from Peshastin, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
25 of 35 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light Socket short
- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.
Parts Used:
-
Rebecca from Gautier, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
22 of 31 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
refrigerator would'nt cool
first i removed the four screws that hold the shelve in place disconnected the wire replace both diffuser-air,reconnected the wire and replaced the screws
Parts Used:
-
arthur from doral, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
20 of 28 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
plastic hook broke
-
Christina from Tacoma, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
16 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Shattered crisper pan glass
-
Stacia from Salem, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
16 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic retainer on end had broken
Just popped it onto retainer nubs on door. Had been a little concerned, as it was replacing part # 240337900, but it fit just fine.
Parts Used:
-
Jonathan from Portland, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
14 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!