CREA650ACW Admiral Range - Instructions

The sensor inserts into a slot in the back side of the range. By removing screws on the heat shield on the backside of the range, the sensor wires will be exposed can be unplugged. Then remove the screws that attach the sensor to the back inside panel in the oven. Next, pull the old sensor out. The wire leads will get caught on the insulation blanket, no big deal. Reverse the process to install the new sensor. The new sensor comes with two connector sets for the wiring. I did the whole job for less than the cost of a service call.

We lifted the glass top, uninstalled the old burner and installed the new burner in it's place. It worked right away - and is still working. No other tricks the new burner was a perfect fit.

The video was good but my model had and additional back plate that wasn't mentioned with 6 additional screws to take out and put back in. Other than that the video explained everything including checking the wires, clips. Oven works great now.

I searched Whirlpool, Sears and random appliance stores and Part Select was the only company to have the lens available. All other manufacturers said the lens was no longer manufactured as a stand alone piece and I would have to buy the entire light assembly. Thank you Parts Select!!!!!

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

Pulled stove well away from wall - took plug out of socket..Phillips screwdriver. Slotted element into wire thing-y - one connector fell down the back, so had to take back off the stove. Used tweezers to pull wire back into back of oven. Screwed plate over wire.Was thrilled when I turned stove on and element shone brightly. Husband away so had to do it myself. Had a glass of wine.

It was so easy. The video that was sent to me with my order confirmation made it kids play. Took away any of the fear of doing something wrong. Highly recomend using parts select. Fast servic too!

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

screwdriver

1. Remove power from unit. 2. Removed 1/4" sheet metal screw from lower blower vent tube. 3. Lifted the unit above the counter and placed two 1x2" boards between the unit and counter. To remove the Stove Top to get access to the Element you must remove 8 each 1/4" sheet metal screws from the bottom side of the Stove Top attaching flange. 3 each screws on the forward and aft side and 1 each on the left and right side. (Note, the 8 each 1/4" attaching screws are at the top of the Stove Top attaching flange.) 4. Remove the Vent Grill and locate the 2 each cross point screws on the center left and right side of the opening. (Note. Due to the limited space, I used a right angle cross point driver.) 5. Remove Stove Top. 6. Tag electrical connections. Remove and replace Element. 7. Turn on power and check Element. Remove power and Reassemble Unit.

Unplug Oven. Undid two screws pullout, undid two wires. Plug in two wires, put unit back, put back tow screws. Close oven door, replug oven, turn on oven for test. It worked no fire.

My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.

Removed two screws, pulled out the old element, disconnected the wires from it. Connected the wires to the new element and installed it in with the two screws.

It only took a manner of a few minutes to replace the heating coil in the oven.

I pulled the electric range away from the wall . unpluged the connection. Called my son . I removed the screws from side of the element and we pulled out the wire , one red one white and connected them to the new element. Bingo , done. plugged in the range ,and pushed it backin place. Turned on the oven to see if it works. Good job well done. I'm 77 yrs. and wantd to do it myself, My son, ELECTRICIAN SAID, WAIT MOM. So I did