Models > CREA450ACW > Instructions

CREA450ACW Admiral Range - Instructions

All installation instructions for CREA450ACW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CREA450ACW
286-300 of 310
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

oven would not come up to temperature

  • Customer: Pauline D from Alexandria VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Turned off circuit breaker to oven. Removed old unit by undoing screws and remove from clamp.Put to unit in by placing it to clamps and adjusting so it was level and screwed it back in. Voila! But now I think I need a sensor..

one of my 8" burners got really red in one spot and then had flame.

  • Customer: Pamela from Ballantine MT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
So purchased two new 8 inch elements and replaced them.

Bulb replacement

  • Customer: Judith from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover...released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Burnt out bake element

  • Customer: Janet from Hillsboro ND
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My husband did it and was very easy. Has been done before too. Very fast service from you also. Will order again if we need to.

Door seal was pulled out by grandson.

  • Customer: Michael P from Hickory Hills IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
finished removing door seal, used pliers to remove old securing studs. positioned new seal and pushed securing studs into existing holes and was done.

The drip pans needed replacing.

  • Customer: Alison from Carnation WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Put in the new drip pan -- which are really nice shiny ones.

my wife decided to clean the oven and while holding up element broke the end off. leaving the wire hidden inside.

  • Customer: robert from iva SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Assuming you dont have the same problem as I this will be a very simple repair.Unscrew 2 phillips screws holding the element in place, then gently remove connector wire from each side .careful as it may be brittle and detach itself. Leaving the power wire inside and unreachable from the front of oven. once you have old elemement out slide connectors onto yynew element replace screws and your done

Replacing a faulty bake element.

  • Customer: keegan from Winona MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
1. First make sure power is disconnected from appliance. Either by unplugging unit from the receptacle or by turning off the breaker supplying power. 2. Next remove the shelves from oven, to give yourself enough room to work. 3. Next remove the two Phillips screws holding the two brackets, where the bake element goes into the back wall of the oven. 4. Carefully pull the bake element out from the wall of the oven. Just enough to expose the two wire terminals. 5. Using the pliers carefully wiggle the wire clips off of the spade terminals on the bake element. 6. Remove the old bake element. 7. Connect the new bake element to wires. Make sure that terminals have solid connections before inserting the element into the back wall of the oven. 8. Reinstall the bracket retaining screws. 9. Turn power back on and check that oven and the new element is functioning. 10. Let oven heat for about 15 minutes before placing any food in the oven, as there will be a slight odor from the new element. It will diminish quickly. 11. You're done.

Bake Element burnt in half

  • Customer: Kelly from Register GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I simply unscrewed and removed the old bake element. Then popped in the new bake element according to the directions in the Youtube video that was attached to my order confirmation email.

Dirty drip bowls

  • Customer: Paul from Carnegie PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just remove old bowls from range top and put new ones. That is all ... just super simple! :)

Dirty drip bowl

  • Customer: Paul from Carnegie PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Remove old drip bowl from the range and put a new one back.

Maytag Electric range oven bake element burned out.

  • Customer: Charles F from Melrose Park IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Before starting, shut off power to the range with the circuit breaker or fuse, or unplug the service cord. The bake element is the lower element. Remove the wire oven shelves for easy access. Using a Philips#2 screwdriver, remove the two screws holding the old element to the rear of the oven. Gently pull the element straight out until you can see the connecting wires come through the holes. These wires are connected to the element with spade clips. Remove the clips by pulling them straight off the old element taking care that they do not fall back into the holes. Put the new element in place, connect the wires to the terminals, and slide the assembly into the holes. Replace the two screws, restore the power and you are done.

No problem other than the order shortage of one 8" Drip bowl

  • Customer: Ronald from Crete NE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Had to special order a second one to replace the missing one, but was sent the replacement no charge

unable to remove screw with screwdriver

  • Customer: Emmett from Rayville LA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
used drill to remove old screw

I wanted to purchase new drip pans, since those that I have are a bit grimy

  • Customer: Hedy from Richmond VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I will begin by saying that not only will I continue to order my parts from PartsSelect, but I also highly recommend this business. If you call Whirlpool be careful that they forward your call for parts to some preferred vendor, which a customer might assume is Whirlpool but it is not. PartsSelect is the same type of business, but with outstanding customer service. With regard to the drip pan, Whirlpool had not updated the part number for these as I found out when i called them. Whirlpool no longer uses the drip pans without the holes which is a serious problem since this could be hazardous to the owners of these ranges if you are forced to purchase the drip pans with the holes in them. That said, I ended up keeping my old drip pans, because if you spill grease under the new ones with the holes in them and since the range design with the fan built in on the top does not allow you to lift the top to clean under the pans, you could end up with a grease fire. This is not the fault of PartsSelect and they handled my order in a manner that I would give them a rating of exceptional for customer service.
All Instructions for the CREA450ACW
286-300 of 310