Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CRE9700ACE

CRE9700ACE Maytag Range - Overview

Get Parts and Repair Help for CRE9700ACE

If you know the range repair part you need, you can browse the list of all parts on the CRE9700ACE, or you can search by name or part description. You can also find your part by where it is located on the CRE9700ACE by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for CRE9700ACE parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.91

Light Bulb - 40W

Sold individually.

Order within the next 11 hrs and your part ships today!
$29.46

Long Oven Sensor

This oven sensor kit comes with two harness adapters. This sensor detects the temperature within the oven cavity.

Order within the next 11 hrs and your part ships today!
$19.05

Broiler Drawer Support - Front

Order within the next 11 hrs and your part ships today!
$41.10

Door Hinge Kit

This oven door hinge assembly comes with two screws and is intended for use with many ovens. It can be used on either the left or right hand side.

Order within the next 11 hrs and your part ships today!
$6.18

RANGE ELEMENT CLEANER

Order within the next 11 hrs and your part ships today!
$4.47

Screw

This screw is sold individually.

Order within the next 11 hrs and your part ships today!
$30.30

Rocker Switch

Order within the next 11 hrs and your part ships today!

Latch Lever Clip

Rubber Door Spacer

Sold Individually. This spacer has adhesive on one side. This spacer is used between door panels of ranges and ovens.

Glass Door Foil Tape

This piece of foil tape is twenty-nine and a half inches long. It is three inches wide and adheres to the inside top of a range's glass door.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

burned in half

  • Customer: mike from gold bar, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 518 of 518 people found this instruction helpful
put the new element in the oven pushed wire onto connector on element held it up to match holes and put the screws back in, very easy to change. I really like the fast way I receive a part from you. read more

No heat - element had burst.

  • Customer: John from Marion, IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 231 of 295 people found this instruction helpful
Unscrewed 2 screws holding terminal ends of the element in place. Eased the element out, until the two AC power wires were exposed. Pulled off the connectors from the element terminals (pretty tight fit - needed pliers to remove one of them).

Slipped the connectors onto the new element terminals, and eased the element back into the oven wall. Sec... read more

Bake element burnt out

  • Customer: Glenn from Jupiter, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 130 of 193 people found this instruction helpful
Before you touch anything unplug the range or trip the breaker. Pull the racks out of the oven, it gives more room to work. Remove the two screws that hold the element and pull the element out about 2-3". Disconnect the old element. Before you install the new element check the wire and the connectors for age and heat damage. If the connectors are loose repla... read more