CRE9600CCE Maytag Range - Instructions

removed screws slid element out diconnected electric terminals reconnected terminals to new element slid back in replaced screws turned oven on sucess

shut power off to range. removed oven shelves to make getting old element out a lot easier. removed screws that hold old element to back of oven - carefully pulled old element out about 3-4 inches. pulled power connectors off end of element. then installed new element in reverse order. Very easy to do. My wife could have done,but she does baking. I do the repairing. Thank-you for such great service. Greentown joe

turned breakers off unscrewed two screws, removed old element.Reattached wires on new element,put two screws back in. flipped breakers back on and its good to go.

number 1 was to shut off circuit breaker. Just removed 2 screws pulled out element slowly to expose wire terminals, removed wires carefully so terminal was not damaged. Replace element was spot on so install was in less than 5 min.

killed power...removed back of stove...removed switch and replaced it..reinstalled back...powered up

Removed two screws holding oven sensor in place. Haad to remove part of the back to access wires. Found existing wires had burnt up, and had to reterminate same. Installed new sensor, making sure the leads did not come in contact with the rear of oven compartment. (This may have been what caused failure to begin with)

Turn the power off at the breaker first! then I used a phillip head screwdriver and unscrewed the two screws that was holding the metal plates on, then pulled the element out with the wires connected and pulled off the terminals. Then i put the new element in and hooked the wires to the terminals then pushed back through the back of the oven then screwed the plates back on then it was done!

The "PartsSelect" General discription of the parts funtion helped me to confirm my suspitions that there was some form of temperature registering problem. I whatched the short video they provided on how to change the part out, even though, in this case, it's pretty self explanitory.The part was in my hands a day erlier than promised and in reality, much earlier than I had anticipated from the beginng. It took me all total, 20 minutes to exchange the part out and have the oven in operation again.

The sensor inserts into a slot in the back side of the range. By removing screws on the heat shield on the backside of the range, the sensor wires will be exposed can be unplugged. Then remove the screws that attach the sensor to the back inside panel in the oven. Next, pull the old sensor out. The wire leads will get caught on the insulation blanket, no big deal. Reverse the process to install the new sensor. The new sensor comes with two connector sets for the wiring. I did the whole job for less than the cost of a service call.

We lifted the glass top, uninstalled the old burner and installed the new burner in it's place. It worked right away - and is still working. No other tricks the new burner was a perfect fit.

The video was good but my model had and additional back plate that wasn't mentioned with 6 additional screws to take out and put back in. Other than that the video explained everything including checking the wires, clips. Oven works great now.

I searched Whirlpool, Sears and random appliance stores and Part Select was the only company to have the lens available. All other manufacturers said the lens was no longer manufactured as a stand alone piece and I would have to buy the entire light assembly. Thank you Parts Select!!!!!

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

This particular Amana electric range has a "eye" that can serve as the heat source for a small or large pan simply by using the rocker switch to "flip" between "large" or "small." This switch broke. I found Partselect.com, found the part, ordered on Saturday night and received it on Tuesday afternoon. 1) Shut off power to the range at the breaker box. 2) Used a small flat-head srewdriver to pop the old rocker switch from the appliance. 3) Used a set of locking pliers to hold the wires in place as I disconnected the old switch from it's connections using a set of needle-nose pliers. (It was a plug-in style switch). 4) Plugged in the new switch. 5)Released the wires from the locing pliers. 6) Popped the new switch into the range's cabinet. 7) Flipped the breaker to "On". WORKS Perfectly

Pulled stove well away from wall - took plug out of socket..Phillips screwdriver. Slotted element into wire thing-y - one connector fell down the back, so had to take back off the stove. Used tweezers to pull wire back into back of oven. Screwed plate over wire.Was thrilled when I turned stove on and element shone brightly. Husband away so had to do it myself. Had a glass of wine.