Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CRE955

CRE955 Maytag Range - Overview

Get Parts and Repair Help for CRE955

If you know the range repair part you need, you can browse the list of all parts on the CRE955, or you can search by name or part description. You can also find your part by where it is located on the CRE955 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for CRE955 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the CRE955

[Viewing 1 of 1]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.88

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

$29.74

Long Oven Sensor

This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of your oven cavity. There is an adapter at one end, a probe at the other, and they are connected by an insulated wire. The probe is approximately 7 inches long. You can test the sensor with a multi-meter for functionality. You need to check the model-specific manual to determine what the proper resistance is for your specific appliance. This oven sensor comes with two wire harness adapters and a set of instructions.

$24.04

2 Piece Broiler Pan

This is cookware designed for use in your range or oven. It is a two-piece dish that is used to grill or cook food while the broil function is on, meaning it can withstand high tem...

$50.53

Bake Element (15" long x 19" wide)

This spade style bake element with push on wire terminals is 15 inches long and 19 inches wide. The depth of the terminals is three inches.

$3.75

Hex Nut

This hex nut is an authentic Whirlpool part that is sourced directly from the original equipment manufacturer, and will fit a variety of appliances including ovens, microwaves, ref...

$27.30

Broiler Pan

$29.68

Broil Pan Insert

$58.11

Oven Door Gasket

$59.55

Broil Element Kit

This broil element is a little over seventeen inches long, and is not quite thirteen inches wide. It has screw on terminals and a terminal depth of just over three inches. The term...

Lamp Retainer Gasket

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 120 of 139 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. ... read more

F1-1 code

  • Customer: charles from marstons mills, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 54 of 69 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will ... read more

Repeated oven temperature sensor fault codes.

  • Customer: David from Arlington, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 27 of 31 people found this instruction helpful
First I removed the two philips screws inside the oven that hold the element in place. Then I pulled the sensor out and the two insulated wires through the hole to reveal the plastic connector. I unsnapped it from the connector and replaced it with the new element. Then, behind the oven, I removed five or six philips screws on the right side of the large ... read more