Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CPR1100ADW > Instructions

CPR1100ADW Magic Chef Range - Instructions

All installation instructions for CPR1100ADW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CPR1100ADW
16-30 of 34
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven taking 30 mins to preheat and stinks like gas.

  • Customer: brian from granite falls, WA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
*Oven floor panel was blocked by fan guard.*

Had to remove fan guard first as I have the convection feature. Easy. 6 screws.

Replaced the oven floor panel, stained and warped.

Checked the ignitor switch by trying to preheat oven. Switch heats up but not enough to ignite gas.

Replaced the Ignitor. Easy. Plug and Play. Replacement insulation comes with the ignitor.

Thank You Parts Select. Youre my new favorite website. I can't wait until my next appliance breaks down.

floor panel heavily stained and warped

  • Customer: Joel from Monroe, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
slide latches in rear of floor panel forward and remove.

Stove top had burnt marks from long use

  • Customer: MEEWAN from BUENA PARK, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Just replaced the top.
No tool or repair was needed.
Parts arrived earlier than promised, so it was awesome!

The floor panel of the oven was pocked and in bad shape

  • Customer: Roger from San Juan Capistrano, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 6 people found this instruction helpful
I found the panel on the innernet, ordered it and when it arrived I removed the old one and replaced it with the new one.

Replacing warped oven floor panel

  • Customer: Linda from Staten Island, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Very simple and stressfree - popped out old - popped in new.

Oven not evenly cooking food

  • Customer: Steve from Tyngsboro, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
If your food is not cooking evenly, a warped floor panel with attached difuser (or "v" shaped heat shield) may be the cause. Simply slide the 2 clips to unlock the panel and move the entire assembly up-and-out (back first) and slide the new one in. Be sure the clips are lined-up with the holes in the back of the oven. The new floor panel comes with the new heat shield.

Broken leveling leg.

  • Customer: Don from Crestwood, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

Screws on the door of the dishwasher were very loose.

  • Customer: Kathryn from Carol Stream, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!

Used stove was missing 1 leg.

  • Customer: Clarence from Monroe, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.

Leveling legs were broken during the summer

  • Customer: Jayne from Willimantic, CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.

Rubber seal was broken

  • Customer: Jennifer from Lynn, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Broke the same day I installed it

Oven temperture over 500 at any setting - thermostat

  • Customer: David from Suffield, CT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Shut off the gas before you do anything! Remove the top front face cover by removing the four screws. Remove the three gas lines that go into the oven valve. remove the screws that hold down the manifold bar. Slide bar to the front and free from the burners and main valve. Remove the small bolt on the underside of the manifold that holds in the oven valve to the manifold. Remove old thermostat bulb from it's bracket inside the oven and pull through to the top of oven. Then remove the old valve. Remove rubber seals and transfer them to the new valve if you don't have new ones. Replace the new valve. Insert thermostat bulb on the end of the wire into the hole and down into the oven. Mount thermostat bulb into bracket. Then just reinstall in the same order that you took it apart. Then run the oven and check the new thermostat out to make sure it is working properly.

enamel on old panel was destroyed...

  • Customer: Lee from Truckee, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
take out the old, put in the new !.. wanted to do the same with the oven racks, but $100 for 2 seem to me as gouging, other than that = satisfied....great web site.... woody

As easy as it could be

  • Customer: Phillip from Twentynine Palms, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I have worked in maintenance field most of my adult life and all aspects and to change the oven door gasket was no challenge what so ever. It took longer to find my needle nose pliers to remove the old gasket clips and then re-install the new gasket. Maybe 10 minutes total

Missing Oven Rack

  • Customer: Janine from Hatfield, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I think the installation instructions are fairly self explanatory. This is the second item I've ordered from Parts Select and I'm thrilled with their service. The items are always less expensive than other sites and they deliver what they promise. I would highly recommend them.
All Instructions for the CPR1100ADW
16-30 of 34