Models > CPEB30S9DC2 > Instructions

CPEB30S9DC2 Frigidaire Oven - Instructions

All installation instructions for CPEB30S9DC2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CPEB30S9DC2
1-15 of 43
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not heating to desired temperature

  • Customer: Dan from Bellevue ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 50 of 71 people found this instruction helpful
Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven and attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove.

Broil element wasn't working...

  • Customer: Kevin from Alexandria VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 27 of 35 people found this instruction helpful
I pulled my unit out of the wall and noticed that the insulation around the top broiler element was a bit brown. Closer inspection revealed that the element had shorted somehow to the oven itself and caused the element to become non-functional. I tried measuring the resistance first, and it was within typical values for the other elements, but I decided to replace the element anyway.

I ordered from PD and the part arrived just a few days letter by regular shipping. I undid the screws holding in the element, undid the wire connectors and replaced the broken element with the new one. The element worked like a charm and I was back in business for cooking.

Cracked oven door inner glass

  • Customer: Mitch from Fernandina Beach FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 27 of 39 people found this instruction helpful
Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after removal; this holds the door at a 45 degree angle for easy removal. After that, just place the door on a flat surface and dismantle the door from the inside. The inner glass is contained in a metal frame with another piece of glass; this frame comes apart easily using the clips in each side. The door assembles easily after the glass is replaced; just take your time and give yourself enough room to lay out the parts as you go. Good luck!

Cord was not tightened enough by delivery crew.

  • Customer: Timothy from Spring Valley AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 29 of 51 people found this instruction helpful
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

Oven door hinge broke causing the door to fail to close properly.

  • Customer: James from Chickamauga GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 16 of 30 people found this instruction helpful
I ordered the part based on the parts list provided. The part arrived by mail 2 days after I submitted my order by email. True to the word in their website, they mailed the item the same day I placed the order.

It took approximately 20 minutes to remove the damaged hinge and replace the new one. No problems at all and I was extremely pleased with the rapid arrival of my order. I had studied the door and the hinge placement in advance and knew exactly what was needed. The only tool I used was a screwdriver. I removed the plate on the side of the door...lifted out the damaged hinge...replaced it with the new hinge...replaced the plate covering the hinge parts and replaced the door on the oven. An easy fix....

Element burned up.

  • Customer: Lynn from Denton TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 12 of 18 people found this instruction helpful
Removed old element and plugged in new. Very simple.

The hinges were worn out and the door would not close.

  • Customer: Guadalupe from Bakersfield CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 13 of 25 people found this instruction helpful
I removed the door with instructions from the owners manual, printed out the door parts diagram from your web site to determine how to take door apart to replace old hinges with the new ones, what took long was cleaning the door glass surfaces while I had the door apart being carful not to break the glass, do not use a green pad to clean the dirty film from cooking on the glass surfaces I did and it left scratches on the glass. I used alot of common sense and reversed the takeing the door apart process to put is back together.

Broken glass interior oven door

  • Customer: stephen from garden grove CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 13 of 27 people found this instruction helpful
Had to reference original owner's manual for instruction(s) on how to remove oven door. Used several "YouTube" videos to reference oven door design (Oven door glass is actually several layers of glass.) After completing about 30 mins of research and finding the right square drive bit, the repair went smoothly and without complications. The biggest challenge was researching and understanding what part(s) were needed and how to replace them. It seemed liked a lot of work doing the research however it sure beat a $350 repair bill. It cost me $90 and about 1 1/2 hours of total time. Oven works better than ever, thanks parts select for the part(s) and diagram(s) ...

replacing the fan on a convection oven (fan was making a vibration noise)

  • Customer: John from Stevensville MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. Once there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.

Oven light stayed on & smelled like electrical burning.

  • Customer: Vincent from Brunswick GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 9 people found this instruction helpful
Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven light switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal.

Oven Door wouldn't staty closed & dropped open HARD

  • Customer: April from Centennial CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 21 people found this instruction helpful
On a beautiful Saturday morning, we began the oven repair by argueing about who should hold the door, and who should use the screwdriver, we managed to remove the oven door by unscrewing 8 screws (2 top, 2 each side, 2 bottom). The bottoms were the most difficult as the incredible hulk must have done the original assembly. The door was heavy & awkward and the new hinges have a little lock that must be unlocked in order to hook it inside the frame. Of course the screwdrivers we had all had long handles, so after some shouting about where all the shorter handled ones were, I found a stubbie at which my husband gave me a dirty look. After more grunting & shouting we got the door back on.

broken lens over oven light

  • Customer: Leslie from Warsaw VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 10 people found this instruction helpful
Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

bottom oven element not heating

  • Customer: dempsey from eastland TX
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 47 of 174 people found this instruction helpful
replaced bottom oven element, did not fix the problem. replaced the thermostate and the terminal block and that did not fix the problem. parts select what is next?

Broken door hinge. Door became heavy. Later came off on one side.

  • Customer: Judy from Mukilteo WA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Husband/wife effort. We located our manual for removing the door and followed instructions. (It's probably online as well.) With the door off, we removed the screws on the side with the defective hinge, took out the old hinge and put in the new one. In trying to replace the door, we couldn't get the lock (upside-down u-shaped piece on the hinge) to rotate over the hinge lever hook on the new hinge. It looked slightly different than the other side (had a bit more hook on it that was in the way). PartSelect sent a new hinge in case the other was defective. (The first arrived in 2 days; the second in 3. No extra charge. Very pleased with the service!) Same trouble. So we filed off the tip of the hook and were able to move the lock in place and put the door back on. The door is not heavy anymore, but doesn't pull in tightly at the top. We thought about taking it off again and trying to position the new hinge a little better to see if it will fit perfectly (it slants down a little compared to the other side.) But it's not so loose at the top that the oven light comes on, so it's usable the way it is. And it looks good, so we're leaving it.

Oven would not heat after running self clean

  • Customer: Michael from Owasso OK
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Googled the problem and found Oven Temperature Sensor and Main Terminal Block to be the most likely problems. Turned out to be neither. No parts were needed. Oven has a thermal overload switch on the rear upper left. Thermal overload needed re-set. To do so you have to remove the oven, remove the back and press the red button on thermal overload. Biggest challenge was figuring out how to remove the oven. Even with the installation manual it was not easy to fgure out. The instructions are misleading. You need a special tool. I used two hacksaw blades as a substitute, and slid them in to release the clips. Once you figure out how to get the oven out the rest is simple.
All Instructions for the CPEB30S9DC2
1-15 of 43