Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CNNT198K (AF51A)

CNNT198K (AF51A) Maytag Refrigerator - Overview

Get Parts and Repair Help for CNNT198K

If you know the refrigerator repair part you need, you can browse the list of all parts on the CNNT198K, or you can search by name or part description. You can also find your part by where it is located on the CNNT198K by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for CNNT198K parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the CNNT198K

[Viewing 2 of 2]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.02

Screw

This screw is sold individually.

$47.35

Capacitor

This capacitor is also known as a run capacitor, and it is most often used in refrigerators and freezers. This part provides the voltage or energy current required to start the compressor and keep it running. It allows the compressor in your appliance to easily cycle on and off. Doing so enables the appliance to effortlessly maintain its internal temperature. If the capacitor is faulty your refrigerator or freezer might be too warm, or you may notice the compressor will hum, but it will not run. When replacing your capacitor, you should check the old one for any signs of damage, overheating, or arcing, as that may suggest there is a bigger problem with your appliance.

$37.73

Condenser Fan Motor Kit

This condenser fan motor kit is designed for use with refrigerators. This fan draws air through the condenser coils and over the compressor. It does this with the goal of cooling t...

$3.02

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

$2.96

Screw

Sold individually.

$3.02

Screw

This screw is sold individually.

$5.00

Plastic Tubing

This part supplies water to refrigerator components that require water, such as the ice maker and water dispenser. If you notice a leak coming from your refrigerator, the plastic t...

$70.21

Evaporator Fan Motor - 115V 60Hz - Blade NOT Included

This is an evaporator fan motor for a refrigerator. The fan motor circulates air through the refrigerator to the fresh food compartment for efficient cooling. It is just over three inches long. It is made of both metal and plastic, and is made up of black, white, and metallic pieces. Disconnect power from your refrigerator before starting the repair because you will be working near electrical circuits. This is an authentic replacement part that is sourced directly from the original manufacturer. It is important to note that the blade is sold separately and is not included with the evaporator fan motor.

$4.79

Screw

This screw is sold individually.

$23.38

Icemaker Fill Tube

This fill tube grommet is used to supply water to the icemaker and is partially located in the refrigerator/freezer wall.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

My refrigerator stopped cooling and the freezer section stopped freezing

  • Customer: garth from forest lake, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 218 of 242 people found this instruction helpful
I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck let's give her a shot ... read more

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 131 of 141 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

cocktails running out of ice

  • Customer: Craig from Westminster, CA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 51 of 56 people found this instruction helpful
filled both ice cube trays up with water and placed in the freezer.. within hours my ice oproduction was doubled! no more warm cocktails : ) read more