CNE2000ACW Maytag Range - Instructions

Donna from Dallas, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

471 of 478 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drip bowls needed to be replaced

took old bowls out, put new bowls in, took a coffee break

Parts Used:

John from Chester, VT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

453 of 542 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Stove top element not working due to bad receptacle.

Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.

Parts Used:

Richard from Carthage, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

191 of 208 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old drip pans stained

Replaced old drip pans with new ones - very easy - even a 68 yr old lady can do it!!

Parts Used:

Linda from Atlanta, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

216 of 425 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

one of my burners would only work half the time, and you had to wobble it to make it work

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected the new element using the wire caps, and finished bye rescrewing the element backinto place.

Parts Used:

cindy from Sebeka, MN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

138 of 265 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

We needed new drip pans and no one carried the model we needed

we removed the old pans after first removing the electric heating element and simply inserted tne new pans

Parts Used:

sylvia from ventnor city, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

67 of 71 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burned terminal block and filter board

Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.

Parts Used:

Terminal Block

Joseph from Decatur, GA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set, Wrench set

90 of 192 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replaced drip bowls in stove

Took out the old drip bowls and replaced with new bowls.

Parts Used:

Liza from College Point, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

69 of 132 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Rented appartment in which none of the drain pans were the proper size making it very difficult to cook

I removed the element and then the drain pan and replaced with the new correct pans. I replaced the element and all was well.

Parts Used:

Grace Mary from Canton, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

65 of 129 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Purchased home but stove had no broiler pan.

Purchased 2 piece broiler pan from this site

Parts Used:

2 Piece Broiler Pan

Raymond from BLOOMINGTON, MN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

14 of 20 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner was out but the burner coil worked on onother burner

Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.

Parts Used:

Richard from Orange, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

10 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner receptacle burned out

Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.

Parts Used:

Michael from N. Haverhill, NH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

8 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven would not heat

For an oven this old, and not to mention a somewhat unique size, I did not expect to find any replacement parts. I removed the screws from the back of the oven; cut the wires; installed new high temp connectors by crimping them on to the wires; connected and installed the new bake element. The fit was practically identical!

Parts Used:

Bake Element

Luis Ruiz from Duluth, GA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

7 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Stove top wouldn't come on. Oven couldn't go higher than low heat

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

Parts Used:

Terminal Block

Peter from FREDERICK, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set

7 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

electric coils would not stay flat as drip pans were incorrect fit

replaced drip pans with correct type

Parts Used: