Models > CMV1000BAQ > Instructions

CMV1000BAQ Maytag Microwave - Instructions

All installation instructions for CMV1000BAQ parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CMV1000BAQ
1-15 of 23
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Turntable wheel broke off

  • Customer: R. from Hudson FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 15 people found this instruction helpful
Just replaced it with the part that was sent -- no physical tools used.

The part was sent when promised and arrived promptly. I would recommend this company for part replacements.

No Power to Microwave

  • Customer: John from Palos Hills IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 16 of 31 people found this instruction helpful
After determined the problem on one of the websites...I received the part I needed... removed the control panel and installed the new main fuse In about 15 mins!

Microwave turntable would not turn

  • Customer: Frederick from Scottsdale AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
Turned off circuit breaker to microwave. (Built-In microwave). Unscrewed four screws at bottom panel of microwave to expose electrical wires/plastic plug to existing microwave motor.
Disconnected plastic plug/clips to motor and microwave lights(to allow entire bottom panel to drop down fully from back hinges). Unscrewed mounting screw for motor and removed old motor. Replaced motor and screwed mounting screw back in. Re-attached electrical connections for motor and lights. Closed panel and screwed bottom panel back on. Turned circuit breaker back on. 15-20 minutes start to finish.

Glass Carousel Tray broke

  • Customer: John from Crows Landing CA
  • Difficulty: Very Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 7 of 14 people found this instruction helpful
I propt the door of the microwave open using a chain and come along. I then used an engine cherry pick to hoist the Glass Carousel Tray up and level with the floor bottom of the microwave. once it was level I slid the tray over onto the center of the microwave and set it down slowly. I then rmoved the chain and come along and shut the door.

our glass carousel broke right in half, after a gradual crack developed.

  • Customer: Doe from Madison CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 8 people found this instruction helpful
I popped in the new tray, and that was that! A perfect fit!

Microwave would not heat food. All other functionality was working as expected

  • Customer: James from Staten Island NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 8 people found this instruction helpful
I disconnected the power. Took off the front panel that was held together by two screws. Reviewed the schematic that was inside. Located the switches, saw which lead was burnt. Unscrewed the two screws that held the switch in place, cleaned the connector, and put the switch in and connectors back. Powered the device, tested for cooking/heating functionality. It worked, Closed the front panel

Needed to replaced the glass carousel Tray

  • Customer: Carlene from Portland ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
The replacement would have been easy - remove the glass tray and put the new one in,

The rollers on the turntable guide had broken lose.

  • Customer: Floyd from Hot Springs AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
Lifted out the glass turntable plate and removed broken turntable guide. Placed new turntable guide into place and replaced the glass turntable plate.

old wheels wore out

  • Customer: Lateshia from Campbellsville KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
took out old turntable and placed new one in

turntable roller for plate

  • Customer: Daniel from Chestertown MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
open door, place roller in the microwave, put the glass plate back in place -- done.

wrong part

  • Customer: Jeff from Littleton CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
easy nothing to it. A cave man could have done it

Replace Glass Cooking Tray

  • Customer: Allen from West Valley CIty UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
The circular glass tray for my mother's microwave was accidentally broken. Fortunately, PartSelect made it easy to locate and to order a replacement.
As for the repair, I opened the door and put it in. The work was done faster than it took me to type this email.

Turn table was intermintant

  • Customer: kevin from navarre FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
The motor would turn about 10 revolutions then quit. I would manually spin the motor and it would turn about another 10 revs and quit again. The motor I ordered was an exact match OEM and install time was less than 30 min total to install the motor, secure the electrical and the bottom of the microwave. Thanks Partselect for the prompt delivery and ease of using your web sight.

turn table inop.

  • Customer: Glen from Lebanon TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 7 people found this instruction helpful
first removed four screws lower panel, one motor screw,electrical connector, and reversed procedure done. To add a little to this repair story, we had a recall on our maytag dish washer, asked if at the same time they could bring a motor out for microwave, they said no without diag. time, also told them I'd pay for install, even if my diag. was wrong, and the part also, there lose! Thank you all having the correct parts at a very reasonable price.

Replacing broken glass tray

  • Customer: thomas from port charlotte FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
This was the second company I ordered from, the first one from them didn't fit and then they advised no replacement existed. Hopefully I will get a refund for the wrong part sent back. This time part select sent the right part the first time and it fit right away. Many thanks.TC
All Instructions for the CMV1000BAQ
1-15 of 23