Models
>
CLZ8505BDB
CLZ8505BDB Magic Chef Cooktop - Overview
Sections of the CLZ8505BDB
[Viewing 2 of 2]
Keep searches simple, eg. "belt" or "pump".
Top Burner Igniter
PartSelect #: PS2082000
Manufacturer #: 74004053
This is a surface burner igniter, also known as a top burner ignitor and stove top spark electrode. It is used to generate the spark that lights the surface burner. If your stove will not start, eleme...
$41.20
In Stock
Rubber Grommet
PartSelect #: PS2202491
Manufacturer #: Y8007P02060
Used as the bottom feet of a gas stovetop grate. Sold individually.
No Longer Available
Burner Head Cap with Spark Electrode
PartSelect #: PS11741734
Manufacturer #: WP3412D025-09
This is a burner head cap with spark electrode for your range, and it distributes flame evenly to your cookware. It does this by steering the gas to the back and front burner heads, which will divide ...
$119.17
In Stock
Igniter Knob
PartSelect #: PS11744002
Manufacturer #: WP74002414
This igniter knob is less than two inches in diameter and a little over an inch high. It is a black knob with white lettering along its perimeter.
$23.67
Special Order
Regulator Kit with Fitting
PartSelect #: PS2002939
Manufacturer #: 12001285
This part will cut off the flow of gas to your appliance once it reaches a certain pressure.
No Longer Available
Oven Igniter
PartSelect #: PS11744543
Manufacturer #: WP7432P097-60
Used with RV ranges.
No Longer Available
Questions And Answers for CLZ8505BDB
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the CLZ8505BDB
[Viewing 3 of 3]Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
gas burner ignitor failure
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed t
... Read more
hat rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order.
Read less
Parts Used:
-
roy from East Providence, RI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
139 of 157 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
porcelan on igniter broken (2)
remove 2 screws that hold element in place, remove element, replace with new element, and replace screws , replaced burner assy on other
Parts Used:
-
paul from mc neal, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
31 of 45 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The grommets came apart metal from rubber.
I replaced the broken grommets with the new ones. I purchased 8 so I would have back ups because I did not feel the new one would last either. I think they cost TOO MUCH but I could not haggle for price.
Parts Used:
-
Frank from Pierce, ID
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
23 of 27 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!