CGR3765ADC Magic Chef Range - Instructions

Removed glass and then two screws to remove metal plate pulled out socket,disconnected two wires and installed new socket.

I am so gald I found Parts select. I was going to order a Gas valve for $140. All the comments said the problem was a bad igniter. even though the igniter was glowing bright it was not drawing enough pawer to open the gas valve. I purchased the igniter installed it in 15 minutes and my oven works like new.

Removed old igniter. Porcelain was broken. Replaced with new igniters. Really simple to do. Took 10 minutes to replace all 4

Followed the excellent instructions on your web site. I removed the oven burner assembly to make it easier to install the new igniter. The connector on the new igniter matched the one in my oven exactly. It helps to have the oven light on!

There was a lot of trepidation about starting this project. What if this is the wrong part? What if I hook it up wrong? What if the gas line is not properly secured when I'm done? This is why it took my 6 months to start this project. I hesitantly looked up my product number online and partselect.com returned three of the top ten results so I clicked it. One of the best moves I've made. When the product was shipped, I received an email with a video attached that explained how to install the igniter. This is what set partselect.com apart from everyone else and differentiated my experience from a "maybe i'll look around more next time" to "I will use partselect for all of my appliance part needs from now on" experience. Thank you for the quality customer care.

Remove oven door and bottom panel. Remove metal shield above the burner. Unscrew old igniter from brace. All this was straightforward. Then I found the old (long) igniter did not have a convenient plug that I could pull through the hole in the back of the oven. So I had to clip the two wires to remove the old igniter and stripped the insulation of these wires. Then I clipped the two wires of the new igniter since, unfortunately, I could not use the convenient plastic connector. I stripped the wires of the new igniter and connected both to the previously stripped wires coming through the hole from the back of the oven. I twisted on the ceramic wire nuts provided. It took 10-15 minutes or so to be confident these wire nuts wouldn't just fall off on their own. Then I stuffed the wire nut connections back through the hole, stuffed in all the insulation provided (necessary for the new (short) igniter!) and screwed the new igniter to the old brace. (I didn't need the new brace supplied or two long wires supplied.) Total time was about 70 minutes. The oven works well! This experience is much better than finding a repairman, scheduling the visit, etc.

look up part, read the diognosis, order part, watch repair vidioe, order part, install mystelf. success!

The repair itelf was quite easy, the problem is the ingition rod is 1/32" too short and goes directly to ground not acheiving a strong enough arc to ignite the gas. I had to remove polish and install the original rod in the new brner to achieve funtion. So never throw away the old parts until you are certain all funtions correctly. This is not parts select problem, most likely non checked function test at factory level.

it was really simple with the kit and instructions that came with the kit everything i needed was in the kit, and hats off to you guys

followed video took 10 minutes, almost went anf bought a new stove

First, I called Sears who wanted $440.00 to send a tech out to repair the stove. Second, I visited various web sites to find out what the problem was. I watched a brief video on Part Select which showed the repair of the stove. I then checked other parts stores on the web and selected Part Select based on price and video. Installation was very easy just as the video showed. Stove was repaired in less than 30 minutes.

watched video provided when ordered part; follow the steps, easy as pie

Undid screws on front and some on the back and replaced part and put screws back on and it fixed the proble

The only difficulty with following the supplied video, is that my ignitor did not come out as easily as a few turns of the screwdriver. The screws stripped as I tried to remove them, making them twirl in their holes. I had to apply back pressure for them to come off and free the ignitor for replacement. Other than that, the installation went smoothly, and the oven sprang to life within 10 seconds of turning it on.

I simply followed the "general" instructions from the online video "Partselect" provides and perused the instructions included in the kit. The OEM igniter was much longer than the replacement but the new part was spec'd just fine. It was necessary for me to open up the back of the stove in order to retrofit the igniter leads to the original block connector and install the heat resistant padding included in the kit. The additional necessary hardware fit very nicely inside the oven. The stove's oven fired up without any problems and spared me the expense of purchasing a new oven. Thank you very much "Partselect".