Models > CGR1425ADW > Instructions

CGR1425ADW Magic Chef Range - Instructions

All installation instructions for CGR1425ADW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CGR1425ADW
1-15 of 241
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven wouldn’t heat up properly

  • Customer: James from Berwick ME
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 133 of 147 people found this instruction helpful
My oven has two igniters so I needed to determine which one was the problem.

Using the amp/multi meter I tested the connection between the igniters and the valve, with the oven turned on, to find the bad igniter. Depending on the model of stove you have, the amp reading you need for a properly functioning igniter will vary. My lower igniter read 2.7 amps with a rated amp between 3.3 and 3.6. So that was the culprit.

Replacing the igniter was easy. Two screws and a wire connected with a plug. I was able to do the diagnosis and unplug the wire without pulling the oven out. I pulled the drawer out and removed the two screws in a cover behind where the drawer was. You may not be so lucky…I have long arms.

I found removing the oven door made it easier to reach the igniter itself. To remove the door just open it slightly and pull up, it should come off easy…and replace in opposite manner.

Keep track of your screws and put it back together the way you found it except for the igniter that is.

Anyone with moderate technical skill could easily do this repair. The diagnosis is the hard part. I estimate I saved about $200 doing it myself.

Good luck.

F1 code - gas over would not heat.

  • Customer: george from birmingham AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 72 of 80 people found this instruction helpful
Repair tech checked oven and said the control panel was bad and needed to be replaced. The new control panel would cost over $450.00! I found that the oven sensor was bad and replaced it for $30.00. The old oven sensor had failed following a self cleaning cycle. I found that the wires coming out of it were burnt.

Replacing the oven sensor was very easy. I removed the back panels 6 screws to gain access to the sensor's connection. I then removed the 2 screw that hold the sensor in place inside the oven and pulled the old sensor out through the oven. I reversed this process to place the new sensor in the oven.

gas burner ignitor failure

  • Customer: roy from East Providence RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 66 of 75 people found this instruction helpful
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order.

Our oven would not heat up, smelled like gas.

  • Customer: Theresa from Yorkville IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 40 of 45 people found this instruction helpful
I removed the oven door, unscrewed a couple of screws, replaced the ignitor, put screws back in, done! Sometimes it would take my oven up to an hour to heat up and sometimes it just wouldn't heat up, just fill the house with a gas smell. Now, it heats up in about 3 minutes!! We were considering buying a new oven, we will just keep this one. $40.00 beats $700.00

Temp couldn't be increased

  • Customer: Joseph from Muncie IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 33 of 40 people found this instruction helpful
I unpluged the electric cord. I removed 4 screws holding the back cover on. I removed 4 screws holding the control unit on. Unpluged the control unit at 2 places.
Very easy repair.

Oven would not turn on

  • Customer: William from Newkirk NM
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 30 of 35 people found this instruction helpful
First I pulled out the oven from the cabinet. Disconected the power, I removed the cover from the back, disconected the wires from the igniter. Removed the igniter from inside the oven. Reversed the process to install the igniter. Turned on the oven, it worked. Sat down and had a beer.

Stove wasn't reaching the set temperture.

  • Customer: Paul from Horizon City TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 27 of 29 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Replaced the element and attached the wires. Making sure I pushed the wires back through the hole far enough so the wires wouldn't touch the back of the stove. I then replaced the sensor by removing the two screws and pulling the wire through the hole so I could disconnect them. I reconnected the new sensor and made sure I pushed the wires back through the hole far enough away from the back of the stove. Replaced the screws and was all set to start the stove. I started the stove and it took about 10 min. to reach the set temperture. The stove worked great.

top burners on stove won't ignite ,no clicking noise

  • Customer: scott from centreville VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 28 of 42 people found this instruction helpful
remove small panel on right side of stove,then un clip moduke and put wires from old module to new one.
Exact fit nomproblems.

oven wouldnt maintain temperature

  • Customer: Patricia from Plainfield IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 22 of 26 people found this instruction helpful
First I removed the oven grates and then the metal plate that covers the burner and igniter.Then I removed the two screws that hold in the igniter,be careful because the threads on the sheet metal screw strip off easily due to the heat. Then I slid out the storage drawer on the bottom of the stove.Next I removed two screws that hold on a cover in front of the gas valve where the igniter is plugged in.I unplugged the old igniter, removed it then replaced it with the new one.I then reassembled everything in the reverse order.I did have to use a nut and bolt to replace the damaged sheet metal screw.

2 front burner (RIGHT AND LEFT) doesn't work

  • Customer: Johana from Philadelphia PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 17 of 20 people found this instruction helpful
That's easy...unscrew the 4 top burner and open it slowly.
Open the tube's nut...i used the wrench.
Then install the new one.
And put it back together like before the first thing, and we got 2 burner worked.
It takes about 20-30 minutes.
Thanks Partselect.com
Now i know where i have to go if i need something special part for my household.

Broken front burner gas lines

  • Customer: Richard from Salinas CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set, Wrench(Adjustable)
  • 16 of 19 people found this instruction helpful
The biggest challenge with the repair was propping up stove top. This range doesn't have a prop arm, and the burner assemblies are attached by screws to stovetop. DIY'ers take note: take a minute to learn how your stove is designed before attempting to clean it by lifting the stovetop too high and breaking the front burner gas lines like I did on mine. Fortunately the new burner assemblies fit perfectly with no gas leaks, and the stove is working good as new. Thanks PartSelect!

Oven rack lost in a garage fire

  • Customer: Bob from Saint Clair Shores MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 16 of 19 people found this instruction helpful
First I opened the door to the oven. Then I opened the box that the part came in. (knife) I then slid the oven rack out of the box and unwrapped the plastic, being careful not to bend or scratch the new rack. Now, this is the tricky part... I had to move the existing rack down one space to make room for the new one. Then carefully slid the new rack in, tipping it slightly and sliding it in. LOL

Oven & Broiler Failed to Ignite

  • Customer: John from Baltimore MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 14 of 14 people found this instruction helpful
First I removed the oven door for easier access then, removed the oven grates and bottom pan. Then there is a wing nut that holds the heat deflector in place over the manifold thats needs to be removed. Now you can see the igniter, remove the 2 small hex head screws and disconnect electrical connection.
Simply reverse the sequence to reinstall.
This may sound like alot to do but it only took 15 minutes to complete and I'm not an appliance repair person. Anyone who is somewhat of a handyman can accomplish this job.

Oven would not heat- Beeped nonstop and flashed F3

  • Customer: Erin from Greenwich CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 14 of 14 people found this instruction helpful
First I removed two screws that hold the oven sensor in place. I then removed the screws that held the panel on the back of the oven. I simply unclipped the plastic adaptor and replaced the old sensor with the new one. I screwed the sensor back in and put the back panel on. turned the power back on to the oven and hit the bake button. Voila!! The oven turned on and now it works like new!!!

worn out door seal

  • Customer: Stella from Charlotte TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 14 of 15 people found this instruction helpful
removed old clips and remaining parts of old seal...new part already had clips attached, so just snapped them into holes in oven door.
All Instructions for the CGR1425ADW
1-15 of 241