CG200B Jenn-Air Cooktop - Instructions

The repair was super-easy, the hardest part was removing the old screws and switch. I slid a putty knife under the old switch and used that to pry up while I unscrewed the nuts. The new switch was a very snug fit on the two studs, which was nice, but the nuts included with the new switch were too small as-is. I could have driven a punch through to increase the diameter, but I kept my old nuts and re-used them instead.

Since the other three burners sparked, I traced the problem to the switch on the valve shaft. To replace, (after unplugging the power cord) I pulled off the knobs, removed the two screws on the valve cover (inside the downdraft vent) and pulled the switch up the shaft to remove. I transferred the spade terminals to the replacement switch, oriented and installed.

The lids are fastened to the underside of the unit by rivets....3 to each lid.
I used a cordless drill and small drill bit to drill through the rivets to remove the old lids and remains of the rivets.
The new lids are easily fastened back using a rivet gun ( about $20 in Lowes) using small 1/8th aluminum rivets.
No real problems.
1 thing to note is that the drill bit will pass through the old rivet by about 1/4 inch before it comes up against the upper level of the BBQ floor so do not drill any deeper.The aluminum rivets are easy to drill through and you will easily feel when the rivet is drilled through.

Important: Down load the helpful assembly diagram for the fan motor and study it for a few minutes. It's very straight forward. Also a good idea is to remove the bottom panel which comes off easy before starting.

My only problem was removing the existing blower/fan wheel without damaging it once I had the assembly on the work bench. It was rusted on tight and managed to remove after a few tries using penetrating oil. The wheel is in stock and I'd suggest buying a new one along with the new motor if I had to do the job again.

Bottom line; the fan motor fit perfect but did have to re-use part of the old existing electric pig tail because the motor does not come with the factory type motor terminal connectors. By using three twist on wire connectors was back in business. The down draft vent works like new.

Wife is happy...

Wade

None of the surface burners (two Uni-burners) would light without using a match. I first ordered two replacement PS2089818 top burner spark electrodes. I replace one which was very easy - the electrode just clips into the burner - and I traced the wires down to the back bottom of the stove where I found they plugged into an ignition module. The new electrode didn't help, but since all four burners were out it made sense that the ignition module would be the problem and not the two separate electrodes. So I ordered a new ignition module. It plugged in easily with the terminals well marked like the original. I put the original electrode back in and all four burners now light properly with the desired "tic tic tic" sound with the knobs in the "high/light" position.

Be sure to turn power off; then follow the instructions on the older posts.

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

Very easy repair. Disconnected the old fan switch, replaced with new one...The only problem with the new one is the round nuts that come with the new switch are not big enough to fit around the fixed posts on the stove...The solution...I saved the old ones.....

I removed the burner knobs, unscrewed the 2 screws and removed the cover. I pulled the old switch off the stem and removed the wires. I reconnected the wires to the new switch and pushed it in place on the stem. After checking to make sure the new igniter switch worked, I replaced cover tightened the 2 screws and replaced the knobs. Job done in 5 minutes!

Simply remove old control knobs and replaced with the new ones. I talked to the saleswoman and she was extremely helpful and assured me it was the right part. And it was.

Unplug and pull range away from wall.
Remove metal panel from back of range by using nutdriver to remove 4 screws.
Use phillips scewdriver to remove 2 screws holding old spark module.
Unplug 4 wires from spark module and note placement of wires for reinstall.
Install new module by reversing procedure.
Slide range back against wall and plug in.

Entire process took less than 30 minutes.

NOTE: Spark Module received from partselect.com did not match old part exactly. The screw holes on the new part did not line up with screw holes from old part. I reinstalled new part with just 1 screw. Was told by partselect customer service that the part I received had been substituted and would work fine. It does work but it did not fit correctly.

Removed 2 screws and lifted the control panal. Replaced the switch. Could not use nuts that came with the switch. Had to reuse the oringinals.

The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.

We've been wanting to replace these parts ever since we moved into our home. It was an amazingly easy process. The range looks like new. PartSelect was a great company to work with. You could track your product's mailing status easily online. One of the grates arrived with several scratches on it. When we contacted PartsSelect, they immediately sent us a new grate. We are very pleased with this company, and we will use them for future appliance parts needs.

:-) - Just removed the old one and replace with the new one. Nothing to it. Takes 30 seconds.