CG100L Jenn-Air Cooktop - Instructions

I watched a You Tube video,removed and dismantled the door, installed the new hinge. I forgot to remove the small pin which is similar to a rivet. When I tried to close the door it bent. Eventually, I remembered the shipping pin and pulled it out with any damage. Believe it or not, I had read about the shipping pin on customer comments on PartsSelect...Good luck, it is relatively easy!

The spare part came within two days after I place the order on line. I drew a simple wire diagram of the faulty switch-regulator. Shut off the power to the stovetop, before removing the four terminals on the faulty switch-regulator. I pushed the old regulator up from the center pin and replaced it with the new regulator. The next step was to reinstall the four wire terminals using my wire diagram. Final step was to turn the power back to the stovetop and test the new switch-regulator.

Easily removed the switch housing. After that, the other experiences really helped me as the retainer rings on the old switch would not come off and I broke one of the threaded posts about a eight of an inch from the base. I pried the other one off, more carefully, with a screw driver and a vice grip pliers . I was already to use the "super glue" solution when I luckily found an old nut that fit the one remaining threaded post.

The only problem was the little push nuts that came with the new part were too small for the posts on the stove top. I had to go to hardware and buy some for about 10 cents that fit. Other than that, everything was great. Great service from this company!

Disable cicuit! remove 2 screws on control housing, lift housing. Remove retaining washers from mounting posts (a trifle difficult, but drill into them with an 1/8" bit...they'll break off enough to grab with needlenose pliers). Mount & wire new switch. The replacement retaining washers are too small...hold them in visegrips & ream the hole with a larger drill bit. Place washer in a magnetic hex drive bit, align over post & tap with hammer to start them, then use a small socket to tap them home. Screw down control housing. Enable circuit...voila!

Easily removed the housing - difficult part was removing old fasteners from posts - took 20 minutes caerfully using knive, needle nose pliers, screw driver. Used old fasteners - new ones provided were too small for posts.

My daughter & I followed the instructions in your video and had fun repairing the door. The video showed exactly how to do the repair. I hope I don't need any appliance parts very soon but I will certainly pull up your web site if I do. Thanks for an excellent instruction video.

John - Hot Springs Village, AR

Bought a pair for needed door hinges for replacement. Found a DIY video on You Tube showing technique to replace. Door removal was a bit awkward but hinge replacement and door reinstallation was as detailed in video. Could not nor would not have tackled this project without video. Premium quality parts sent and received within days of ordering. Wife happy therefore so am I.

My son did the repair for me. It was easy, he said. just slid it out and put new one in.

My wife help take the door off. It was a little heavy . The door came apart very easy and went back the same way.We save over $300 by doing it our selfs.

Although only one side hinge had snapped, I replaced both sides with new oven door hinges. Followed the website video installation directions and all went well; the new hinges work perfectly.

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

Broke both crimp on washers. Drilled two appropriate holes in a dowell rod, used these holes to hold the new crimp on washers. Then drove the washers onto the switch's built in pegs.