Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CEW30EF6GSJ

CEW30EF6GSJ Electrolux Wall Oven - Overview

Get Parts and Repair Help for CEW30EF6GSJ

If you know the wall oven repair part you need, you can browse the list of all parts on the CEW30EF6GSJ, or you can search by name or part description. You can also find your part by where it is located on the CEW30EF6GSJ by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your wall oven. We’ve also included any installation videos we have for CEW30EF6GSJ parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the CEW30EF6GSJ

[Viewing 5 of 5]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$27.67

Oven Temperature Sensor

The temperature sensor detects the temperature within the oven cavity. If there is a limited amount of heat, it is not heating evenly, or the oven will not start, this might indica...

Order within the next 11 hrs and your part ships today!
$3.52

Main Terminal Block Kit

Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to operate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.

Order within the next 11 hrs and your part ships today!
$8.21

Anti-Tip Kit

The anti-tip bracket kit comes with one metal bracket and two installation screws, and is sourced directly from the genuine manufacturer. It prevents the freestanding oven, range, ...

Order within the next 11 hrs and your part ships today!
$8.76

Foot Leveling Leg

Sold Individually. These legs should be adjusted to make your appliance level on uneven flooring.

Order within the next 11 hrs and your part ships today!
$90.26

6" Radiant Element with Limiter - 1200W

This is a six-inch radiant element with limiter. It works in conjunction with your stove top range. The purpose of this part is to heat up the cooking area that is located on top o...

Order within the next 11 hrs and your part ships today!
$6.50

Screw

Sold Individually.

Order within the next 11 hrs and your part ships today!
$120.34

Dual Radiant Surface Element - 9"/6" - 3000W

Order within the next 11 hrs and your part ships today!
$46.74

RACK

Order within the next 11 hrs and your part ships today!
$5.59

Leveling Leg

This part is sold individually. The leveling leg is black in color and measures approximately 2 inches in length. It is made of plastic. The leveling leg is found underneath your r...

Order within the next 11 hrs and your part ships today!
$28.96

Oven Door Light Switch

Order within the next 11 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Above 400 beeper went off & code numbers came up on read out

  • Customer: Russell from Lake Havasu, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 61 of 70 people found this instruction helpful
Cut off power at fuse panel. pulled stove out from wall went behind stove removed back panels in area of sensor that I could see from the front side, inside oven. Located sensor from rear & unpluged senser from wiring bundle reached inside oven & removed screws from sensor. Pulled sensor out & threaded wire through hole. Took old & new sensors to bench in... read more

Cord was not tightened enough by delivery crew.

  • Customer: Timothy from Spring Valley, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 60 of 100 people found this instruction helpful
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screw... read more

Oven wouldn't operated. Error code F9

  • Customer: Richard from Centennial, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 34 of 39 people found this instruction helpful
I called a repair place. They charged $54 to diagnose, (said it needed a new latch motor) then wanted $220 to complete the repair. I checked online prices and did it myself for about 15 minutes work and the latch motor itself ($44?).

Was necessary to uplug the range, pull it away from the wall and remove the back panel sheet metal, then 3 screws ... read more