Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CES366HQ0

CES366HQ0 Whirlpool Range - Overview

Get Parts and Repair Help for CES366HQ0

If you know the range repair part you need, you can browse the list of all parts on the CES366HQ0, or you can search by name or part description. You can also find your part by where it is located on the CES366HQ0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for CES366HQ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.91

Light Bulb - 40W

Sold individually.

Order within the next 7 hrs and your part ships today!
$5.15

SCREW

Sold individually.

Order within the next 7 hrs and your part ships today!
$7.22

Touch-Up Paint - White

18ml

Order within the next 7 hrs and your part ships today!
$35.96

Oven Door Trim Kit

This white oven door trim set contains three pieces: two for the sides of the door and one for the bottom. The screws are sold separately.

Order within the next 7 hrs and your part ships today!
$11.07

Spray Paint - 12 oz. - White

Order within the next 7 hrs and your part ships today!
$34.96

TRIM-DOOR - Bisque

Includes the 2 side trim and 1 bottom trim - Redesigned parts per Manufacturer.

Order within the next 7 hrs and your part ships today!
$12.31

Anti-Tip Bracket Kit

This kit keeps your appliance from tipping. Comes with bracket, ring and 2 screws.

Order within the next 7 hrs and your part ships today!
$7.11

Hinge Pin Kit

Includes 4 hinge pins. Used at hinges to hold door open so the door can be lifted off.

Order within the next 7 hrs and your part ships today!
$20.80

Spray Paint - Surperior Black

This is a 12oz can of black spray paint.

Order within the next 7 hrs and your part ships today!
$22.95

PRIMER

Order within the next 7 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

F3 Error message

  • Customer: Charles from Brecksville, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 123 of 159 people found this instruction helpful
Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the string still shows thru t... read more

heating element burnt up

  • Customer: Esther from San Antonio, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 64 of 69 people found this instruction helpful
first I pulled the stove from the wall. Then unplugged the stove from the wall (electric stove) for safety. then I removed the middle back panel screws(2) and then the panel. I then pulled the wires off the heating element that was bad. I took the screws (2) off the heating element inside the oven. I had to use WD-40 to loosen the screws because with th... read more

The burner would keep heating after turning off the switch

  • Customer: RON from KAUFMAN, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 49 of 54 people found this instruction helpful
Start by turning off the power to the range.
It was fairly easy to take the "Control Deck" off the top of the range by removing about 8 screws. I leaned the deck forward without removing any wires except a green ground that was held on by one of the screws.
There are two small screws under the switch knob holding the Infinite Switch to the panel. ... read more