Models > CER1115AAW > Instructions

CER1115AAW Magic Chef Range - Instructions

All installation instructions for CER1115AAW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CER1115AAW
106-120 of 187
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ugly looking drip bowl.

  • Customer: Irina from Green Cove Springs FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Repair? What repair? I just removed the old drip bowl and replaced it with the new one. Piece of cake.

Burner control knob/switch shaft had broken off.

  • Customer: Steve from San Luis Obispo CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 4 people found this instruction helpful
Removed front panel of range, removed switch (2 screws), unclipped wires from back of existing switch. Installed new switch - reverse order of above.

Broken leveling leg.

  • Customer: Don from Crestwood MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

OVEN QUIT HEATING DID NOT NOTICE HOLE IN SIDE OF ELEMENT UNTIL I REMOVED IT

  • Customer: BRIAN from FOWLERVILLE MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
UNPLUGGED THE STOVE REMOVED BACK COVER PLATE UNPLUGGEG TWO WIRES REMOVED RACKS FROM OVEN REMOVED TWO SCREWS THAT HOLD BAKE ELEMENT IN PLACE AND REVERSED PROCESS

Worn out bowls

  • Customer: Cameron from Lakehills TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Bowls needed to be replaced.

The oven would not heat (bake element not turn red)

  • Customer: Robert from Mountain Grove MO
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Read the ID number from label and ordered part on line. Part was delivered next day. Shut off power to stove and Pulled stove out from cabinet setting. Took out about 12 screws from back pannel and removed it. Pulled out wires (easily seen) from each side of heating unit at back of stove. Went inside oven and took out 1 screw (easily seen) on each side of heating element at back of oven. Heating elemnet came right out. Reversed procedure for installing. Only tool used is a small Phillips screw driver.

Screws on the door of the dishwasher were very loose.

  • Customer: Kathryn from Carol Stream IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!

needed a new drip bowl and couldn't find ons that fit exactly but you had it

  • Customer: Elsie from Garner NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I removed the old one and put in the new one. Works great!!!!!!!!!!!!

Hot burner light went out

  • Customer: Harold from Russell Springs KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unplugged the range, took off back shield (4 screws) unplugged the old part and plugged the new part in, put the shield back on and plugged the range back in. When you remove the light unit behind the lens after unplugging the two contacts slide it sideways toward you, it is slotted, don't try to pull it straight out or you will break the lens.

Used stove was missing 1 leg.

  • Customer: Clarence from Monroe WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.

TO OLD NEEDED TO BE REPLACE

  • Customer: ROSARIO from MESQUITE TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
ACTUALY I JUST REMOVED THE OLD ONES AND REPLACE THEM WITH THE NEW ONES . AND THANK YOU FOR YOUR PROMPT DELIVERY I FOUND SOME ONE I CAN TRUST .THANKS AGAIN .MRS BOLANOS

rusty pans

  • Customer: Stewart from Hanover PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
simply remove the old and install the new; perfit fit

Element burned out.....

  • Customer: Elizabeth from Ogdensburg NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
the video that was part of the "part shipped" email was a great help....I had no problem replacing the part...Thanks

I needed to replace my burner pans.

  • Customer: Robert from Wilton CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The Drip Pans are a cinch to replace with no tools necessary. The best part is that the Web Site is extremely easy to use, and the parts arrived two days after being ordered.

Leveling legs were broken during the summer

  • Customer: Jayne from Willimantic CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.
All Instructions for the CER1115AAW
106-120 of 187