Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CEI30GF5GSD

CEI30GF5GSD Electrolux Range - Overview

Get Parts and Repair Help for CEI30GF5GSD

If you know the range repair part you need, you can browse the list of all parts on the CEI30GF5GSD, or you can search by name or part description. You can also find your part by where it is located on the CEI30GF5GSD by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the CEI30GF5GSD

[Viewing 6 of 6]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$8.21

Anti-Tip Kit

The anti-tip bracket kit comes with one metal bracket and two installation screws, and is sourced directly from the genuine manufacturer. It prevents the freestanding oven, range, ...

$11.57

Medium Burner - 9.5K

The surface burner head is used for ranges and ovens, and is located on the cooktop, where the flames go up. The surface burner spreads the gas through holes to create an even flame throughout the entire cooking area. If your surface burner is damaged it can affect the distribution of gas, or the flames may not come up correctly. If this is the case, replace this part. The measurements of the surface burner are: 6.25 inches in length, 5.13 inches in width, 8 inches in height, and 0.4 pounds in weight. Allow your cooktop to cool before installing this part. Refer to the manual provided by the manufacturer for further repair instructions.

$6.59

Igniter/Orifice Mounting Screw

$5.11

Steel Washer

This steel washer is also known as the range washer and is used on your oven door. The measurements for the steel washer are a three quarter inch outer diameter, and a one quarter inch inner diameter. This washer is an OEM part, made of steel, which is sourced directly from the manufacturer. This specific steel washer is used with your range, to secure the inner and outer door together and to secure the oven door handle back in place. Users have ranked this repair as a simple installation that should take you less than fifteen minutes to complete.

$41.18

Front Burner Igniter/Orifice Assembly

$92.07

Bake Igniter

The oven burner igniter simply ignites the gas so it can heat the oven burner. The igniter does this by drawing electrical currents through the oven safety valve to open it. If the element shortens out, is no longer glowing, or is only glowing red or orange, replacing the igniter is the solution. You will need a wire splicing tool to do this repair. First, disconnect the wire harness from the igniter by removing the access panel on the rear of the stove. Next, access the front of oven and take out the racks before removing the bottom of the oven. For the rest of the installation instructions refer to the diagram provided by the manufacturer. Remember to unplug your oven from the power source before beginning this project.

$38.88

Sealed Burner Head - 14k

$8.76

Foot Leveling Leg

Sold Individually. These legs should be adjusted to make your appliance level on uneven flooring.

$6.50

Screw

Sold Individually.

$27.80

Top Burner Orifice - 9.5k

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven wouldn't operated. Error code F9

  • Customer: Richard from Centennial, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 35 of 40 people found this instruction helpful
I called a repair place. They charged $54 to diagnose, (said it needed a new latch motor) then wanted $220 to complete the repair. I checked online prices and did it myself for about 15 minutes work and the latch motor itself ($44?).

Was necessary to uplug the range, pull it away from the wall and remove the back panel sheet metal, then 3 screws ... read more

anti-tip bracket not installed

  • Customer: Brian from Panama City Beach, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 30 of 38 people found this instruction helpful
I was selling my home and did not realize that the anti-tip bracket was not originally installed. A home inspection caught the problem and the buyers required that I install one. I could not find the original and obviously the installer never put it in place to begin with. The buyers wanted this resolved within a week so I had to act fast. I could not fi... read more

The burner would not light by itself, and the flame was lopsided.

  • Customer: Roland from Auburn, ME
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 20 of 23 people found this instruction helpful
The repair was nothing, but the diagnosis was a bit tricky. After carefully looking at the burner head, (cast aluminum) I pretty much figured out that the 4 small cast aluminum bumps that keep the burner cap positioned up in the air the correct amount to allow gas to flow under the cap, were worn down, preventing the gas from exiting properly by the igniter... read more