Models > CE4317L2

CE4317L2 (PCE4317L2) Amana Washer - Overview

Get Parts and Repair Help for CE4317L2

If you know the washer repair part you need, you can browse the list of all parts on the CE4317L2, or you can search by name or part description. You can also find your part by where it is located on the CE4317L2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for CE4317L2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$7.64

Drum Support Roller

This roller is for square-ported models and has a metallic bearing in its center. They are sold individually and most dryers use 2 rollers at the rear and it is recommended to repl...

$13.80

Multi-Rib Belt

At 93-3/8" in length, this flat dryer drum belt has 5 ridges and is 3/8" wide.

$4.41

Drum Glide

This drum glide is sold individually. ***Please Note: these should be replaced in pairs.

$4.80

Idler Pulley Wheel with Bearing

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$5.99

High Limit Thermal Fuse

Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when ...

$4.46

Thrust Washer

$19.70

Idler Lever

The spring for this part is sold separately.

$10.77

Door Catch Kit

This kit comes in two pieces: the catch and the clip.

$2.70

Retaining Ring

Sold individually.

$17.87

Cylinder Felt Seal

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replace drive belt

  • Customer: Robert from Skokie IL
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 133 of 150 people found this instruction helpful
Remove front panel, lint basket, motor mounts,exhaust hood, front drum brackets. Then slip serpentine belt around drum, pressure w/ tension idler pulley and slip around drive motor spindle. Replace all parts in reverse order (a two person job).
Vacuumed inside of dryer (full of lint.) read more

Squeeling/Screeching

  • Customer: William from Round Mountain NV
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Socket set
  • 155 of 228 people found this instruction helpful
First I read all of the other stories about this problem so I would have the correct parts. At $6 a roller, decided to get all 3 & a belt. Pulled the lower panel off (2 bolts), then the door (2 bolts). Marked the door switch wires. Took 2 bolts out of the top & tilted it back. I found this the easiest way to access the drum. Mark 2 wires before disconnecting... read more

Support Roller removal and Installation

  • Customer: Fred from Chicago IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 134 of 197 people found this instruction helpful
First I turned off the gas supply line. Then unplug the dryer. Remove bottom front cover by removing the 2 screws (1 at each side) at the bottom. Next remove the 2 screws (1 at each side) located at bottom of front door panel. Pull front panel away from dryer and pull down slightly. This will disconnect the entire front panel(with door) from dryer. Carefull ... read more