Models > CE2950XYW3

CE2950XYW3 Whirlpool Dryer - Overview

Get Parts and Repair Help for CE2950XYW3

If you know the dryer repair part you need, you can browse the list of all parts on the CE2950XYW3, or you can search by name or part description. You can also find your part by where it is located on the CE2950XYW3 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for CE2950XYW3 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the CE2950XYW3 [Viewing 3 of 3]

$12.52

Thermal Fuse

This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins...

$13.44

Multi Rib Belt - 92-1/4"

This dryer drum belt has four ridges, three grooves and is 1/4" wide.

$18.12

Cycling Thermostat

Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermostat has a limit of 155 degrees Fahrenh...

$4.55

Door Catch Kit

This dryer door latch kit comes with one plastic door latch and one metal door strike.

$28.20

Thermal Cut-Off Kit

This clothes dryer thermal cut-off kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). This kit also includes...

$17.15

Drum Support Rollers

These two drum support rollers are no longer available for individual sale. Available in a package of two and it is recommended that you replace both rollers at once. These two rollers come with four tri-rings.

$3.46

Leveling Foot

Sold individually.

$11.73

Idler Pulley Assembly

This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum. This arm is what attaches to the idler pulley wheel.

$23.25

Lint Filter with Handle

$85.42

Drive Motor with Pulley

This motor fits most Whirlpool incorporated dryer brands before 1996. NOTE: Pulley is NOT available separately.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was working, but no heat.

  • Customer: ANTHONY from CHESHIRE CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 914 of 1055 people found this instruction helpful
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, ... read more

No heat but would run otherwise

  • Customer: Dana from Grassvally CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 488 of 494 people found this instruction helpful
Cleaning the lint out of the whole machine took quite a bit of time--it was everywhere. Underneath the lint trap was a collection that ultimately ruined the thermal fuse where it restricted the air flow considerably.

Ascertaining the problem was the most time consuming part.

The actual repair was quite simple and didn't take but 15-20 m... read more

No Heat

  • Customer: Vernon from Niceville FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 482 of 485 people found this instruction helpful
First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back off. read more