CDNT18V9A (AC48A) Admiral Refrigerator - Instructions

The ice maker change out was easy. The problem was the part came with a different filler cup but the one needed was supplied. Changing to the other cup required taking the ice maker apart and installing the other filler cup. Go to the parts list and find the filler cup. Use instructions found there to change to other cup and then install your ice maker.

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

removed old icemaker and transfer some of the parts to the new icemaker. The only problem was that I had to disasemable the new icemaker to replace the fill tray with the older style (which was included). Once that was done, installation was pretty easy.

I removed the old ice maker as described by the DIY video and had no problem except, I had to remove the ice tray from the motor section so the end cap could be changed. This only required removal of two Phillips screws on the case of the motor assembly, that are used to to secure the tray. Once the tray was off, the ice ejector could be removed and the end cap was free to change. Everything was re-installed in reverse order and unit was mounted. An FYI to anyone with slow ice making, will need to check their freezer temperature. Make sure it's set to get as cold as 5-10 degrees Fahrenheit. After installing new maker, it was not making ice fast enough, only to find my freezer temperature needed to be changed as well. Everything is working as it should now.

My husband put in in, no problem and all is well. My husband is a mechanic for large machinery/motors so installation was no problem. Thanks, better than buying a new fridge!!!

The ice maker was easily replaced, however I still had no ice. I ended up using an on-line repair service which determined that the problem was the water inlet valve. Replacing it was beyond my expertise so I hired an appliance repairman.

just as video instructions said, very easy just following them ,part arrived in very short time and was exact fit completely satisfied, saved repair man service charges and wait time

After reading the articles previous owners wrote, I tackled the repair. There were no big problems until I had to change out the water line on the icemaker tray--that part was for a different frig--so it had to be changed out with the Amana water line part that was enclosed. I couldn't get that part removed, so I had to have my husband change it out. He then finished the installation. Everything went smoothly, just my pride wanted me to finish it all by myself.

Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

Replacing the auger assembly was easy. Unfortunately it did not fix the problem, which was a weak auger motor. The motor would not turn the auger when a piece of ice would go into the area where the blades push it out. It would instead stop the motor and make it screech. This happened with every third piece of ice. Replacing the motor, which I bought elsewhere (couldn't find on this site) fixed the problem.

got the model number off the fridge. ordered the part. received the part. the funnel part that drains the water into the tray was broke when I received the new icemaker, I took the one that was on my old leaking icemaker an put it on my new one along with the old hardware parts {wireharness, ice level bar}. followed the video instructions an wahlah nomore ice in the bottom of the freezer or in the floor. it looked like the funnel was broke in shipping. its great to have ice because its fixing to get hot!

removed condenser fan -located behind refrigerator next to compressor, Not much clearance to work, there are 3 screws to remove from condensing motor,sounds easy but clearance is lacking to remove them ,(takes alot of PATIENCE). Then you have to remove the fan blades to be able to get clearance to remove motor!! I wouldn't reccommend trying this repair unless you are a pro.

After receiving the new ice maker assembly I placed the new part next to the old one to see what I needed to transfer from the old to the new. After removing the wiring harness and a few small parts, I placed them on the new assembly. After that it was a snap which timewise took about 15 minutes. I am pleased to say the ice hopper is full and being replenished very efficiently.

1. Prepare the new ice maker by installing the bail cut off from old unit and installing the wiring harness from old ice maker. 2. Turn off the freezer unit only and turn off water supply. 3. Unplugged the electrical connector from the ice maker to the plug in back of freezer compartment. Remove the three (3) screws holding ice maker in place. Placed the cap from old unit to new ice maker. 4. Plug the electrical connector to the plug in back of freezer. Attached new unit with the three screws. Place bail in on position and turn the freezer and water on, ice made in circa 3 hours (without leaking I might add :)