CCR567W Jenn-Air Cooktop - Instructions

This was a range top. i removed the 12 hex machine scews holding on the top, then removed the two star screws holding the old switch. there were fore wire that had fitted on tabs. Hooked them to the new swtch and reassembeld. Easy repair since i could lift the unit out without disconnecting main cables. Replacement range would have been oveer $1000. Psrt was under $40 and delivered in a matter of days.

Replaced original switch with replacement sent using the part finder tool of PartSelect. Everything went fine EXCEPT the replacement switch's H1 terminal did not correspond to the original switches H1 terminal. Proper terminal connections were as follows:

Original Replacement
----------- -----------------
L1 L1
L2 L2
P P
H1 HC
H2 H1

If you get H1 & HC reversed, controls will work correctly for each of the two cooktop elements individually, but when used together, both will turn on/off simultaneously whenever either switch closes.

Lifted stove top from counter, removed screws securing glass top, removed screws from switch housing. Removed color coded wires from old switch, one at a time, and secured them to the new switch. Put it all back together and just like new. Probably saved $200 service call.

Note that this model# is not my exact model#, I couldn't find it - but its almost identical to this newer version of my Maytag glasstop drop-in stovetop.

Also note that these instructions are VERY generic and not detailed, as most all stoves will be different in assembly.

Be advised that you are NOT getting the part you see in the picture. It is going to be a newer part that does the same thing. It's a lot smaller and has an offwhite top. It will STILL work, don't return it! The only difference is that the labels on the connections will be a little different - see the other post here on this page that shows how they differ and what to connect to what. Thanks to them I was able to complete this fix easily!

Close the breaker to the stove to ensure no electricity is running to the stove! Use a voltage tester to make extra sure no electricity is running through the cables, they are cheap at home depot!

Just disassemble your stovetop to get to the area that houses the switches. You will see the switch boxes underneath where your knobs go. Take a picture of all connections if you can so you remember where everything plugs in. You'll have about 3-6 cables connected to the switch depending on your stovetop. There are labels on the old switch (L1, L2, etc) at each electrical connector the cables attach to - probably on the top or bottom of the switch. Write down the connector label and what color wire its connected to. Do this for each connection.

If the old labels dont match your new labels, you have an older switch and need to check the other post on this page that someone posted showing how the old labels translate to the new labels.

Now reconnect everything back the same way you took them off and you are good to go!

Such a simple fix and you'll save hundreds.

Removed the cook top from the counter. Removed the switch housing and then the switch. Found a match and ordered. Part came in 2 business days. Once I put together the housing and connected the wire housing the burner worked perfect. The downdraft fan remained on. Placed a call to Jenn Air service and was asked to disconnect the fan switch. There must be some memory in the solid state portion of the switch. After a few mins I replaced the fan switch and hooked up the wiring. All worked fine.

Knocked breaker removed stove top from iland removed a dozen screws replaced switch put screws back in installed top back in iland put breaker back in worked purfect.

turned off power to stove top..lifted unit out unscrewed top and switch had 2 screws re-placed switch and put back together.. make easy $100 plus switch

I removed the glass top and replaced the switch unit successfully. Hardest part was removing the unit from the countertop and bracing the base with a 4x4.

This was a repair project on a Jenn-Air built-in stovetop, which I had trouble finding instructions on how to disassemble. My particular problem was that three of the four burners had no temperature control. They were either on high or off - no such thing as simmer. This is opposite the problem described as a normal indicator of burner control failure. Usually the burner just goes dead. The hardest part of the repair was accessing the metal plate the burner controls are mounted on. First, I flipped the circuit breaker to the stovetop. It will shock the cr@#p out of you if you don't (I have experience from poking around down there without turning the power off). First, I had to remove the two burner inserts. The left one lifted from the top and the right one lifted from the bottom. Don't lift them past about 30 degrees. They are meant to lift up just enough to clear the tray well and then slide out. After removing the burner inserts, I was able to unscrew the eight fasteners holding down the stovetop rim. After removing this, I pulled out the trays underneath the burner inserts and put them aside without unscrewing the ground wires that attach them to the stovetop chassis. After removing the two screws holding on the active burner indicator lights, I was able to pull it up and lay it aside. Then I had to unscrew the two large brackets under the cabinet to loosen up the stovetop chassis so I could lift the front of it up an inch from the cabinet to enable me to unscrew two small metal screws that attach the metal plate holding the burner controls. After removing the two screws holding each burner control to the metal plate, I could unplug each of the five wires from the old controllers and plug them into the new controllers, in turn, before reattaching the new controllers to the metal plate. After repeating this procedure two more times, I reversed the process to reassemble the stovetop and voila, turned on the power and it worked perfectly. The result; a happy wife. For today.