Models > CCR467W > Instructions

CCR467W Jenn-Air Range - Instructions

Installation Instructions for parts on models starting with CCR467W

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

Models starting with CCR467W

All Instructions for models starting with CCR467W
1-7 of 7
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

old switch had shorted and burned out

  • Customer: Larry from Hampton Cove AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 13 of 18 people found this instruction helpful
This was a range top. i removed the 12 hex machine scews holding on the top, then removed the two star screws holding the old switch. there were fore wire that had fitted on tabs. Hooked them to the new swtch and reassembeld. Easy repair since i could lift the unit out without disconnecting main cables. Replacement range would have been oveer $1000. Psrt was under $40 and delivered in a matter of days.

switch for burner, when turned on, would set breaker to off

  • Customer: Gail from Sedona AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 1 of 4 people found this instruction helpful
Lifted stove top from counter, removed screws securing glass top, removed screws from switch housing. Removed color coded wires from old switch, one at a time, and secured them to the new switch. Put it all back together and just like new. Probably saved $200 service call.

Surface Burner Short

  • Customer: John from San Antonio TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed the cook top from the counter. Removed the switch housing and then the switch. Found a match and ordered. Part came in 2 business days. Once I put together the housing and connected the wire housing the burner worked perfect. The downdraft fan remained on. Placed a call to Jenn Air service and was asked to disconnect the fan switch. There must be some memory in the solid state portion of the switch. After a few mins I replaced the fan switch and hooked up the wiring. All worked fine.

Water boiled over burnt out switch

  • Customer: Eddie from Loyall KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Knocked breaker removed stove top from iland removed a dozen screws replaced switch put screws back in installed top back in iland put breaker back in worked purfect.

burner switch broken

  • Customer: larry from houston TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
turned off power to stove top..lifted unit out unscrewed top and switch had 2 screws re-placed switch and put back together.. make easy $100 plus switch

1 burner wouldn't work, and caused the breaker to trip

  • Customer: Jeff from Houston TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I removed the glass top and replaced the switch unit successfully. Hardest part was removing the unit from the countertop and bracing the base with a 4x4.

Three of four burners were inoperable

  • Customer: David from Woodbridge VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
This was a repair project on a Jenn-Air built-in stovetop, which I had trouble finding instructions on how to disassemble. My particular problem was that three of the four burners had no temperature control. They were either on high or off - no such thing as simmer. This is opposite the problem described as a normal indicator of burner control failure. Usually the burner just goes dead. The hardest part of the repair was accessing the metal plate the burner controls are mounted on. First, I flipped the circuit breaker to the stovetop. It will shock the cr@#p out of you if you don't (I have experience from poking around down there without turning the power off). First, I had to remove the two burner inserts. The left one lifted from the top and the right one lifted from the bottom. Don't lift them past about 30 degrees. They are meant to lift up just enough to clear the tray well and then slide out. After removing the burner inserts, I was able to unscrew the eight fasteners holding down the stovetop rim. After removing this, I pulled out the trays underneath the burner inserts and put them aside without unscrewing the ground wires that attach them to the stovetop chassis. After removing the two screws holding on the active burner indicator lights, I was able to pull it up and lay it aside. Then I had to unscrew the two large brackets under the cabinet to loosen up the stovetop chassis so I could lift the front of it up an inch from the cabinet to enable me to unscrew two small metal screws that attach the metal plate holding the burner controls. After removing the two screws holding each burner control to the metal plate, I could unplug each of the five wires from the old controllers and plug them into the new controllers, in turn, before reattaching the new controllers to the metal plate. After repeating this procedure two more times, I reversed the process to reassemble the stovetop and voila, turned on the power and it worked perfectly. The result; a happy wife. For today.
All Instructions for models starting with CCR467W
1-7 of 7