Models > CCGX2620W > Instructions

CCGX2620W Jenn-Air Cooktop - Instructions

All installation instructions for CCGX2620W parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CCGX2620W
1-7 of 7
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

stove top gas burner ignitor only flicks but does not light burner

  • Customer: Marlene from Dana Point CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 9 of 11 people found this instruction helpful
If you have a burner that begins to constantly flick without lighting, and/or flicks while you are lighting another burner, it is likely time to order a new ignitor. Once received, we first lifted the burner support rack, then the burner cap, then unscrewed the nut holding the metal bracket that holds the ignitor in place (years ago we had to "soak" the nut with a loosening spray prior to being able to unscrew it, so since then we do not tighten the nuts too tightly so that each nut is easy to unscrew by hand or with pliers if necessary). The previous steps allow one to lift the burner ignitor up and out of its resting hole. It will be connected to the electric wiring via a plastic connector. All one has to do is pull the wiring away from the ignitor and then push it up into the new ignitor. The plastic connector protects you from touching the live ends of the wiring. Voila! The burner lighted successfully.

two small burners were worn out

  • Customer: Ronnie from Los Angeles CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 3 of 4 people found this instruction helpful
started with turning off gas and unplugging electric then removed right side of stove top that exposed burners removed plastic igniter switch from top of burner valve and in very tight area used 1/4" combo wrench to turn hex screw on underside of burner valve once broke loose the rest was easy just patients and a little determination removed and everything in reverse to install works fine

Conversion back to natural gas From propane

  • Customer: Robert from Mullica Hill NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench set
  • 3 of 5 people found this instruction helpful
I converted the cooktop from propane to natural gas, the parts I was told I needed were the incorrect parts. I called because I was not sure about the listed parts. I was helped over the phone but recieved the LP parts. The flame was very low, and i found the orifices I replaced were the same parts I just took out.I contacted Parts select and they were helpful and credited my purchase without any hestitation.Once the new orfices were recieved it was easy to install. I recommend using a nut driver with sticky tape to go the orifice holder after the venture is removed. You do not have to disassembe the stove as long as you don't drop the part. Changing the regulalor was also very easy by removing the gold nut and pulling the white pin out and flipping it over to Nat. The flat side of the pin is labeled LP or NAT. Then just screw the nut back in and tighten. The LP orifices are labeled on the side 0.65, 0.69, and 0.70 the natural gas orifces are colored black, silver , and red. It would be just as easy to go from Natural gas to LP!

As soon as the parts arived it tooks only 1 1/2 hours to get everything fixed

  • Customer: Robert from Pleasanton CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 2 of 5 people found this instruction helpful
took the nuts off &replaced the new ignited

A valve on my cook top went out.

  • Customer: Anna Marie from El Paso TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 1 of 3 people found this instruction helpful
I actually didn't do the repair. I called a service tech, but found it cheaper and faster to order the part myself. It arrived in 2 days. The tech removed the top part of the cook top with a philips screwdriver after that it was easy as unscrewing the valve and replacing it with the new one and tightening it with a wrench. He put the top back on, tightened the screws and that was it.

Igniter switch was inop

  • Customer: Mark from Kingwood TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
It took longer to figure out how to get the selector cover off than it did to replace the switch. Once I had access it was only about a 10-15 minute job to install and put it all back together and operative. Actually a very easy job to do.

Purchased a used stove top with no burner caps

  • Customer: Beatrice from San Bernardino CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Purchase the caps and received them within a reasonable short time and just put them right onto the burners. Easy/Breezy
All Instructions for the CCGX2620W
1-7 of 7