Models > CCGP2820PU > Instructions

CCGP2820PU Jenn-Air Cooktop - Instructions

All installation instructions for CCGP2820PU parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CCGP2820PU
1-13 of 13
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

stove top gas burner ignitor only flicks but does not light burner

  • Customer: Marlene from Dana Point CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 8 of 9 people found this instruction helpful
If you have a burner that begins to constantly flick without lighting, and/or flicks while you are lighting another burner, it is likely time to order a new ignitor. Once received, we first lifted the burner support rack, then the burner cap, then unscrewed the nut holding the metal bracket that holds the ignitor in place (years ago we had to "soak" the nut with a loosening spray prior to being able to unscrew it, so since then we do not tighten the nuts too tightly so that each nut is easy to unscrew by hand or with pliers if necessary). The previous steps allow one to lift the burner ignitor up and out of its resting hole. It will be connected to the electric wiring via a plastic connector. All one has to do is pull the wiring away from the ignitor and then push it up into the new ignitor. The plastic connector protects you from touching the live ends of the wiring. Voila! The burner lighted successfully.

Simply needed a new knob, however...

  • Customer: Shane from Dallas TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 5 people found this instruction helpful
However, I was very happily surprised how fast I got the part even though I did not specify fast shipping.

Griddle "infinite switch" bad and large burner gas valve

  • Customer: Sean from tucson AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set, Wrench(Adjustable)
  • 3 of 3 people found this instruction helpful
turn off gas,
disconnect gas line from stove
remove stove from countertop (gravity held it down - so don't bother pulling out a bunch of screws yet)
move to table
remove stove facia - 4 small screws
loosen large reverse pressure bolds (3/8 socket)
once the facia is removed - you will have access to all switches and gas burners.
the replacemnt of the two switches was simple.
reverse process to re install.
I had my 12 year old there to hold the stove up in a balanced position - it made it much easier - that third hand helps!

Indicator Lens melted and fell back into the control panel

  • Customer: Philip from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I took the back panel off, removed the old lens, installed the new lens. How easy to order from home, receive the part, do the repair and pay less than it costs to simply drive to the parts house. Cool....

As soon as the parts arived it tooks only 1 1/2 hours to get everything fixed

  • Customer: Robert from Pleasanton CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 2 of 4 people found this instruction helpful
took the nuts off &replaced the new ignited

needed the knob for stove

  • Customer: Dawn from Mcdonough GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Put it on simply as that thanks it was a perfect fit!!!!

broken knob

  • Customer: Michael from Shawano WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Just had to push it into place, by hand only

Griddle was scratched.

  • Customer: Cathryne from Marietta GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
Removed old griddle and plugged in new one.

Broken Gas Valve Knob for Jenn Aire Gas Stove

  • Customer: darryl from everett WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Slipped off old one and slipped on new one. The part was the right one and works great. Timely receival of part was great. Communication from you was great

Housekeper broke knob several years ago and left that burner out of service.

  • Customer: Ruth from Gladwyne PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I eventually searched online for a supplier and ordered the replacement knob. Ordering was easy and delievery was quick. Replacing the gas valve knob was easy; just slid it in place. Now all 4 burners are available for cooking again.

Broken cooktop knob

  • Customer: Christine from Jefferson MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just slipped the new knob on with no problem. Very easy.

THE IGNITERS WOULD SPARK CONTINUALLY AND THEN ONE BURNER WOULD NOT GO ON

  • Customer: Diann from Wylie TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
TURNED OFF GAS, UNSCREWED NUT THAT HELD ON THE PLATE UNPLUGGED THE IGNITER AND REPLACED IT AND PUT IT BACK TOGETHER, VERY EASY FIX.

bad screw on cap

  • Customer: Herbert from Awendaw SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replace burner cap
All Instructions for the CCGP2820PU
1-13 of 13