Models > CCG406B > Instructions

CCG406B Jenn-Air Cooktop - Instructions

All installation instructions for CCG406B parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CCG406B
1-15 of 50
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

one of the surface burner knobs melted and then cracked

  • Customer: Ronald from Philadelphia PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 463 of 465 people found this instruction helpful
the hardest part of the whole thing was finding the part... partselect.com made it easy. the part was delivery quickly using regular mail, and I was simply able to slide the new knob on.

Though the part number was the same it did not fit

  • Customer: Gene from Farmington Hills MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 442 of 526 people found this instruction helpful
The knob neck was 1/4 inches to long. Therefore it could not be used.

3 out 4 surface burner knobs were broken

  • Customer: Aaron from Elkton MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 169 of 315 people found this instruction helpful
Simply pulledoff and threw away the old bad knobs and slipped the new ones on in thier place- four working burners now!

Most amazing thing was I ordered the parts one afternoon and they arrived the very next day.

Also, your site was easy to navigate and find what I was looking for. Many thanks!

stem on the dial split, couldn't turn the burner on

  • Customer: Kathy from Bell FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 150 of 289 people found this instruction helpful
threw out the old and slipped on the new dial....

old knobs broken and couldn't turn on burner

  • Customer: Susan from Cherry Hill NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 147 of 287 people found this instruction helpful
Replacement parts fit as suggested by model number (newer parts are a little different but fit fine). Grates look a bit more modern but hopefully will work fine too.
Amazingly fast shipping!

The burner knob brock

  • Customer: Warren from Alexandria VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 146 of 285 people found this instruction helpful
Went broke purchasing the very simple part through you PartSelect Appliance Parts

broken spindel on knob

  • Customer: Stephen from Bethesda MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 145 of 283 people found this instruction helpful
took old off, put new knob on, by hand

Knob broke

  • Customer: Peggy from Ellwood City PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 68 of 132 people found this instruction helpful
pulled it off, went to internet to see if I could find.
Did Find. Ordered and replaced.

cooktop comes with two burners and a grill. I needed 4 burners.

  • Customer: Clifton from Redlinds CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 22 of 28 people found this instruction helpful
Never really used the grill and needed 2 more burners so I just pulled out the grill assembly and plugged in the burner assembly, added the new pan cover and new grates and viola, I had a four burner stove. Still can pop the grill back in if needed. Much less expensive than buying a whole new cooktop.

The right rear burner ignition switch malfunctioned.

  • Customer: Max from Plano TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 9 people found this instruction helpful
Repair is simple as long as you TURN OFF THE CIRCUIT BREAKER first. After that, take off the cover over the switches (pull knobs off, remove 2 screws and lift off the cover), pull the bad switch straight up off the gas valve, pull the two wires off the switch, plug them back onto the new switch, place it back over the gas valve stem, reassimble the cover and knobs, turn back on the circuit breaker, and verify that ignition switch works. Not a hard repair. (HINT: while you are waiting on the replacement part, you can light the bad burner by turning on the opposite burner ignition switch and using that "spark" to light the other burner.)

My burner grate needed to be replaced

  • Customer: Kathleen from Centennial CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 6 people found this instruction helpful
My husband threw a pot holder on the hot (not lit) burner grate.The potholder melted on the grate and we were not able to remove the melted fabric. We ordered a new grate and it looked so good we ordered three more. I am planning to replace the burners next. We'll have a brand new looking cooktop. The cooktop is 15 years old.

old cracked

  • Customer: JOHN from GAINESVILLE GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
pull off old ,add new

Replaced the griddle side with 2 burners

  • Customer: David from Santa Rosa CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 5 of 6 people found this instruction helpful
Not a problem, very simple once I got all the parts I needed...operator at partselect was very helpful and nice to talk to...Thanks for the extra cooking space

my old knobs melted when someone placed a hot cookie sheet on them

  • Customer: Theresa from Davis CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
This wasn't a repair; it was a desperately needed replacement. I simply popped off my old knobs and put the new ones on in less than 1 minute. The new knobs took years off my beloved gas Jenn-Air stove.
The knobs arrived within two days of placing my order. Outstanding customer service. I will order from this company again and again.

One burner would not ignite (no spark)

  • Customer: Mark from Clarksburg NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
Since the other three burners sparked, I traced the problem to the switch on the valve shaft. To replace, (after unplugging the power cord) I pulled off the knobs, removed the two screws on the valve cover (inside the downdraft vent) and pulled the switch up the shaft to remove. I transferred the spade terminals to the replacement switch, oriented and installed.
All Instructions for the CCG406B
1-15 of 50