Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CCG2521W

CCG2521W Jenn-Air Cooktop - Overview

Get Parts and Repair Help for CCG2521W

If you know the cooktop repair part you need, you can browse the list of all parts on the CCG2521W, or you can search by name or part description. You can also find your part by where it is located on the CCG2521W by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your cooktop. We’ve also included any installation videos we have for CCG2521W parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the CCG2521W

[Viewing 2 of 2]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$17.65

Top Burner Igniter

This is a surface burner igniter, also known as a top burner ignitor and stove top spark electrode. It is used to generate the spark that lights the surface burner. If your stove w...

$3.02

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.

$54.55

Sealed Burner Cap with Electrode

This burner cap assembly is sold with the spark electrode igniter and has a 7-inch outer diameter. This manufacturer-approved surface burner is for gas ranges. The surface burner s...

$3.00

Frame Screw

Sold Individually.

$77.31

Pressure Regulator

This valve automatically cuts off the flow of gas at a certain pressure.

$45.37

IGNITER SW

$6.39

Igniter Wire

This igniter wire is twenty-eight inches long.

$4.87

Screw

Sold individually.

$4.87

SCREW

Part might differ in appearance, but functions same as original. Sold individually.

COVER- BUR

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

A burner wouldn't spark strongly enough to light the gas.

  • Customer: Matthew from Brookfield, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 153 of 168 people found this instruction helpful
Replacement of these burners is very easy. You just twist the burner counterclockwise a quarter turn and pull it out. (You may need a big wrench if the range is very old.) Once out, just pull the two wires off and push them onto the new burner. Crimp them on with pliers if they're loose -- mine were. Twist the burner back on.
If the gasket under the bu... read more

gas burner ignitor failure

  • Customer: roy from East Providence, RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 124 of 138 people found this instruction helpful
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt ha... read more

Burner Was Worn Out

  • Customer: arnold from la punte, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 27 of 28 people found this instruction helpful
Burner head arrived when I got home from work. Just timely to cook for dinner that monday night, got the 4 burners disconnect the element from the old burner, then connect element to the new bunners, in less than 10 mins, and I had save estimate $600 buying a brand new stove or gas range, this will last me another5 to 10 years. Especially this time of r... read more