Models
>
CCG2521A
CCG2521A Jenn-Air Cooktop - Overview
Sections of the CCG2521A
[Viewing 3 of 3]Keep searches simple, eg. "belt" or "pump".
Top Burner Igniter
PartSelect #: PS2082000
Manufacturer #: 74004053
This is a surface burner igniter, also known as a top burner ignitor and stove top spark electrode. It is used to generate the spark that lights the surface burner. If your stove will not start, eleme...
$41.20
In Stock
Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.79
In Stock
Burner Head Cap with Spark Electrode
PartSelect #: PS11741734
Manufacturer #: WP3412D025-09
This is a burner head cap with spark electrode for your range, and it distributes flame evenly to your cookware. It does this by steering the gas to the back and front burner heads, which will divide ...
$119.17
In Stock
Frame Screw
PartSelect #: PS11743908
Manufacturer #: WP7101P126-60
Sold Individually.
$7.76
In Stock
Stand Mixer Screw
PartSelect #: PS11742292
Manufacturer #: WP4159193
This screw is sold individually.
$8.63
In Stock
Screw
PartSelect #: PS11751203
Manufacturer #: WPW10253196
Sold individually. This screw is half of an inch long. It is made of metal and it is intended for use with some Maytag brand ranges.
$4.68
Special Order
Igniter Wire
PartSelect #: PS11742785
Manufacturer #: WP5111A360-60
This igniter wire is twenty-eight inches long.
No Longer Available
Valve Screw
PartSelect #: PS3651486
Manufacturer #: W10491986
Part might differ in appearance, but functions same as original. Sold individually.
No Longer Available
Pressure Regulator
PartSelect #: PS11744587
Manufacturer #: WP7510P083-60
This valve automatically cuts off the flow of gas at a certain pressure.
No Longer Available
Questions And Answers for CCG2521A
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the CCG2521A
[Viewing 3 of 3]Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
gas burner ignitor failure
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed t
... Read more
hat rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order.
Read less
Parts Used:
-
roy from East Providence, RI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
139 of 157 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
porcelan on igniter broken (2)
remove 2 screws that hold element in place, remove element, replace with new element, and replace screws , replaced burner assy on other
Parts Used:
-
paul from mc neal, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
31 of 45 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner would not light; ignitor did not produce spark
Take a few screws off the back of the slide in burner module. Take off the back. Unscrew the ignitor screw, remove ignitor carefully, replace with the new ignitor, put the screw back in, put the back back on, try it out! Ours worked after a couple of tries - don't know if the ignitor had to "rev up" by several sparks or we just didn't
... Read more
have it properly installed at first. Anyway, very easy. Did it in my pajamas on a Saturday morning.
Read less
Parts Used:
-
Candace L. from Woodinville, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
16 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!