Models > CAW2762EW0

CAW2762EW0 Whirlpool Washer - Overview

Get Parts and Repair Help for CAW2762EW0

If you know the washer repair part you need, you can browse the list of all parts on the CAW2762EW0, or you can search by name or part description. You can also find your part by where it is located on the CAW2762EW0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for CAW2762EW0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$12.01

Direct Drive Motor Coupling

This coupling kit is used between the motor and the transmission on direct drive washers with no belt. This is the newer version and is made with new metal sleeves for added stren...

$29.84

Direct Drive Water Pump

It is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one.

$16.24

Water Inlet Valve with Mounting Bracket

This part could have either a blue colored valve body or a green colored valve body. There are two ports for water to enter and this valve is compatible with a half inch ID hose. I...

$29.35

Clutch Assembly

A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity washers and black spring for compact washers. As per factory, the green spring (1.24") replaces the black spring (1.46").

$2.52

Suspension Spring

Sold Individually. Appliance takes 3 of this part.

$4.46

Agitator Bolt

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

$3.76

Tub Spring

$2.70

Hose Clamp

$2.03

Lid Hinge Mounting Screw

Sold individually.

$2.03

Pump Retainer

Sold Individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No movement from Basket & agitator

  • Customer: Jeff from Wayne NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 489 of 520 people found this instruction helpful
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor co... read more

Water pump leaking when machine used.

  • Customer: Tom from Granby MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 414 of 430 people found this instruction helpful
The hardest part of this job was pulling the machine away from the wall so the hoses could be disconnected and the machine flipped onto it's back. Putting the machine on it's back does two things. It drains the water left in the bottom of the tub so it won't pour out onto the motor when the old pump is removed, and gives the necessary access to the pump. ... read more

washing machine is slow to fill with cold water

  • Customer: Roy from Nash TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 192 of 207 people found this instruction helpful
My washing machine became slower and slower to fill over the past several months. It also made a loud squeeling noise during fill-up (all this was on the cold water side only). I removed the old water inlet valve and tore it down, expecting to find corrosion or trash that was blocking the valve from opening completely. Turned out to that the rubber diaphr... read more