Models > CAV2004AWW > Instructions

CAV2004AWW Magic Chef Washer - Instructions

All installation instructions for CAV2004AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CAV2004AWW
46-60 of 360
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

WASHER SHAKES AND DANCES

  • Customer: Adrian from West New York NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Wrench set
  • 9 of 11 people found this instruction helpful
NO NEED TO BUY A BRAKE WRENCH NOR THE EXPENSIVE SPRING REMOVER.
ONCE THE DRUM IS OUT THE WASHER TURN IT UPSIDE DOWN AND LOOSE THE SCREWS HOLDING THE TRANSMISSION ABOUT A LITTLE MORE THAN HALF WAY, TO GIVE THE NEW SNUBBER ENOUGH ROOM TO FIT IN, THEM TIGH AND ASSAMBLE EVERYTHING BACK TOGETHER

Squealing noise in spin cycle this did not fix it!

  • Customer: Ron from Oxford MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 11 of 17 people found this instruction helpful
This was easy except for the e-ring which was extremely difficult to remove. When I put the new one on I filed down the bottom of the front edges to make it easier to slide it on. Beware: If you have the washer tipped back against the wall when you do get the e-ring off everything will come sliding off the shaft all at once and go everywhere. These parts are covered with black grease and made quite a mess so you might want to have someone hold them in place so you can gently slide them off one piece at a time.

Loud noise during the spin cycle

  • Customer: John M from Saint Paul IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 14 of 26 people found this instruction helpful
Repair was made by viewing on line video and owners manual. Once the machine was apart, the brake spring was the only tricky patr. Under a lot of pressure so be cautious. old bearing was removed and the new bearing installed. Machine reassembled. no issues.Thanks !!!

Cover of washing machine wouldn't stay open, it fell on my wife's hand.

  • Customer: Edward from Coventry RI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 12 people found this instruction helpful
This is a very simple repair, I opened the top of the washer by inserting a screwdriver between the top and the washer cabinet. There are 2 clips on the front of washer, locate and push in to release top. Lift top with lid attached and remove the 2 screws holding the lid to the top of washer. Remove lid and replace hinge pin and hinge.
Replace lid, close top , all done. Total time about 15 minutes or so. Now the lid will stay up and not fall on someone.

Washer made awful grinding sound then quit spinning

  • Customer: Matthew from DOUGLASSVILLE PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 9 of 12 people found this instruction helpful
I took the bad water pump off installed the new one and hooked up the new drive belt. Overall it took me twenty minutes, not all that hard to do.

Machine growned when washing, brake was slipping

  • Customer: Daniel from Sugar Land TX
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 10 of 16 people found this instruction helpful
Tried to remove brake stator with machine tilted back. Thisforced the stator off center. Removed the 6 holddown springs, water level hose and drain hose. Pull drum & transmission out of the case. Placed the drun on the ground, brake facing up. Replaced the short screws on the brake stator with 2" screws one at a time. Caution the spring has 200 lbs of force. Used 2" screws to back off spring. With spring tenshion released replace parts. Reversed proceedurer. Machine quite. Wife is happy.

agitator broke

  • Customer: Mark from Voorheesville NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 7 people found this instruction helpful
Removed old 'Agitator Auger and Post Assembly' held in place by one bolt and placed new 'Agitator Auger and Post Assembly'. SIMPLE and good price.

Plastic hinge pin broken on top cover

  • Customer: Daniel from Slatersville RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
First push inner tub to left rear, all the way, and
unscrew hinge from inside of tub. repeat same on
right side. lift cover off and unscrew other half of
hinge off cover, both sides.reverse procedures and your done.
Note: always replace both hinge's new while
you have it apart.

The agitator came off

  • Customer: DAOSADET from WASHINGTON DC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 8 of 10 people found this instruction helpful
use the socket with a 10 inch extention remove the existing screw. place the new agitator and screw back. remove the softner container from the broken agitator and snap it to the new one. job done.

The timer would quit in mid cycle. Spin did not drain the water in Permanent Press or Delicate cycles.

  • Customer: Dale from Benton LA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 9 of 13 people found this instruction helpful
I opened the front of the machine. The clips had rusted. One broke and the others were very difficult to work with. I pried the panel open with a large screwdriver. I took the back panel off to access the water pump. I removed the back panel on the electricals to access the timer. To replace the timer I pried off the decorative cover. To get the knob off you have to squeeze in on the timer split shaft while pulling out on the know. This was the second hardest part. (The front panel access was the most difficult). After that the timer clip is easy to loosen and it slides a littel then pops out. Electrical connection was obvious. The motor sping was the next most difficlt part. The spring fits on the rear part of the motor which is most easily accessed through the rear panel used for replacing the water pump. The water pump has three screws holding it and two hose clamps that come off easily with a pair of pliers. Before removing the water pump, I had to tip up the machine and take the belt off. This was also pretty easy. Put it back together and works great again on all cycles.

original Factory Water Pump Bearing seized up

  • Customer: Bill from Mount Pleasant MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 7 of 8 people found this instruction helpful
Vey Easy to Fix. 1)Turn Water off at the wall. 2)Remove access panel on back of washer. 3) Remove Water pump. It is bolted down to the bottom of the washer by three nut head bolts. when loose the pump can be manipulated and tilted so the belt will have slack and most likely fall right off. Have a bucket ready. Remove water hose from top of pump by sgueaing clam with pliars and sliding clamp up hose. allow to drain in bucket. Lift drain hose out from wall and allow to drain through the pump into bucket. remove hose from pump that goet to drain. Replace pump and reverse steps listed above.

Lid switch had deteriated over time and no longer made contact

  • Customer: James from Rochester NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
removed the screw holding the actuator, ordered the new part and replaced it when it arrived. Shipping was really fast and I even received it one day early.

would'nt wash w/out getting hot

  • Customer: Emery from Talladega AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 8 of 11 people found this instruction helpful
just took the front off and then took the old motor off and switched over about 2 parts from the old to the new and then put the new part on and then placed the front back on and it was ready to go

One of the two bolts that holds the motor in place broke off and since the bolts are actually embedded in the motor I had to buy the whole motor rather then just a 25 cent bolt.

  • Customer: Elmer from Fort Campbell KY
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 15 of 33 people found this instruction helpful
First I took the front shield off, then I took the motor off.

Water Pump Failed

  • Customer: Douglas from State College PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Wrench set, Wrench(Adjustable)
  • 8 of 12 people found this instruction helpful
Obvious problem: belt destroyed. The plastic pulley on the motor was damaged beyond repair. Since you can't replace just the plastic pulley, you have to purchase another motor. The machine still would not spin. Checked the pump again. The bearings might be bad. Replaced pump; Success! washer works again. Total repair: belt $15.68, new pulley with motor $132.00, and new pump $80.00. Estimated cost to repair about $228.00. Time to troubleshoot. 1 hour, time to fix 1 hour; Total time in labor about 2 hours.
All Instructions for the CAV2004AWW
46-60 of 360