Models > CAV2000AWW > Instructions

CAV2000AWW Magic Chef Washer - Instructions

All installation instructions for CAV2000AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CAV2000AWW
436-450 of 502
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

In spin cycle, made a loud nosie

  • Customer: Vicki from Pollard AR
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Took the back off, located problem, ordered part, removed old part, installed new one, tilled washer to put belt back on. Whole process not bad at all. Working with this site was so very helpful, will keep in in my favorites or future use. Thank You Parts Select!

washer leaking from rear

  • Customer: tom from roscommon MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed front and rear covers, replaced drive belt, tub hose and pump. simple operation. Washer still has some leakage not as bad as original leak. Think I have main tub seal problem. Going to check all hose clamps and run again. If the main seal is problem I will be forced to buy new as the parts cost and difficulty of replacement will be the important factors.

water leaking into washer tub

  • Customer: Mark from Fairview Heights IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnected hoses and poppped open the top of washer with a flat screw driver from the front. Removed screw holding the water inlet value with a nut driver. Diconnected wires and internal hose from the old valve and attached them to the new valve. Install new valve in place with nut driver. Clossed the top. Reconnected hoses.

Loads of various sizes were out of balance during the spin cycle. Had to adjust the wet clothes frequently.

  • Customer: Don C. from Sedalia MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
First unplugged washer. Found clips on front of machine and lifted the lid back. Took out two 5/16" screws and removed the front panel. Tilted back the washer slightly and took off the drive belt underneath. Started removing the 6 springs with visegrip pliers that support the tub. Then removed the hose on the back left, no pliers needed. Then used pliers to loosen the clip holding the drain hose on the bottom of tub. Moved the clip down, then took off hose. There will be water in the hose, be ready with towel. Watched the video for snubber installation.

Bad bearing on pump

  • Customer: Lon from Monterey TN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Lay the washer on it's side and remove the drive belt. Set back upright. Pry top cover up. Use a small flat bar and try not to damage the porceline. Two hex head screws (one on each side by the tub)holds the frone panel on. Remove those. Panel can now be tilted forward and removed. Pump is on right side. remove the two hoses and save the clamps. remove the three hex head screws holding the pump. Install the new pump and reassemble. Pretty easy.

washer tub out of balance

  • Customer: ALFRED from BERWYN PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
it is best to watch the video before doing this reapir. Once you see that the job is straight forward, making sure not to remove all of the spring screws is very important.

change out pump bearing wore out

  • Customer: Bennett from russiaville IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unhook water lines after shutting off water, unplug power cord.Then move washer out into open space for easy access. Used flat tip driver to push in the spring clip to open the top of washer. Flip top up and had wife tilt the washer back. Once bottom is exposed took belt off the motor pulley. Let washer back down. Use the socket wrench to take out two ( front corners ) screws. Tilt front panel back and lift out off the clips . Water pump is front right corner. Use socket wrench to take out the three screws that form a triangle. Lift out the pump. Have something to catch water from pump . Use pliers to remove the two clamps spring from the hoses . Remove both hose from the pump. Then install new pump in the reverse order and close up washer in reverse order and put belt on . Replace washer in it place reinstall water line and lastly the power cord needs tobe pulg in. Now test the washer.

Had a difficult time getting the last washer on the transmission pully

  • Customer: Vickie from Harrison MI
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed the video

clothes still fairly wet after spin cycle

  • Customer: jim from radcliff KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
tilted washer about 45 degrees off with old on with new belt.TOO easy

Washer would not spin

  • Customer: Steve from Polo MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After inspecting the brake and installing the new pulley/bearing kit the washer still would only spin slowly. Discovered that if the washer agitates at all in the spin cycle then the transmission is shot. So washer was replaced with a new one.

tub making noise during wash cycle

  • Customer: kevin from lees summit MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Watch the videos on it about replacing the snubber ring. Do not remove the whole assembly just loosen enough to get old snubber out and new one in, or you will find it very difficult to get the brake/clutch assembly back together Also I used a 2 x 4 scrap to push and hold the the barrel while removing the six springs. Wear long sleeves as the metal on the washing machine panels will cut you very easily. Belt was just sliding it over the pulley. One other recommendation is take a pictures before and while you are taking it apart for verification of reassembly.

suspect motor bearings. squeeling and smelled burning

  • Customer: Peter from Voorhees NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed your excellent video instructions to change out the motor.

Plastic hinge at back of lid broke

  • Customer: Bill from Kissimmee FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very easy pop-ed up the top from front used my Duroc screw driver removed screw removed lid slid hinge on slid lid back in place attached screw. Make sure you get screw tighten and snug. Job Done!

transmission bearing melted ..

  • Customer: Louis from Dozier AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
put a total new transmission total kit on.

Hole in hose from wear & tear

  • Customer: Richard from Las Cruces NM
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Opened back panel. With pliers, moved the retainer clamps. Used a flat screwdriver to pry off hose from tank. procceded to remove hose from pump. Put new hose on and replaced hose clamps. Tested with a small wash cycle, no leaks. Job done.
All Instructions for the CAV2000AWW
436-450 of 502