Models > CAV2000AWQ > Instructions

CAV2000AWQ Magic Chef Washer - Instructions

All installation instructions for CAV2000AWQ parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CAV2000AWQ
76-90 of 464
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

shakes, noisey

  • Customer: Dan from Lafayette CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 6 people found this instruction helpful
Removed the waterlines. Set the ends in a small pan or bucket to catch the water.Do the same with the drain line.
Keep an old towell handy as water will drain out of the drain pump when you remove the drain hose. Removed the back panel. Use a flat bladed screw driver to pop the top off the two clips in front holding the top down. Lift the top and pull the two screws which holds the front in place. Remove the front and set aside. Underneath, use gloves and the screw driver to remove the six springs by placing the screwdriver through the top hook end about an inch and with both hands lift the spring off. Carefull not to let the blade slip off and bust your knuckles on something,hence the gloves. Lean the machine over and walk the belt off the pulley. Disconnect the small tube in the back left corner from the drum and lift the unit out from the top. Set the drum on it's top and loosen the six screws under the big pulley just enough to pull the snubber out. Replace new snubber, tighten screws. Set drum back in place and reattach springs. Lean unit over and replace belt. Reconnect the small tube, back left corner. Replace the front panel and top. Connect the drain line and replace the rear panel. Connect waterlines and check for leaks. I went ahead and replaced all springs. I recommend replacing the belt while your at it. I'm wishing I would have. It runs like new, gets more water out on the spin cycle and the dryer dosn't take as long to dry the clothes.

washer would not spin.

  • Customer: Robert from South Gibson PA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 9 people found this instruction helpful
tip washer up on wooden blocks.remove drive belt.remove "E" clip from tub drive pulley and remove all the parts.Install new parts in kit as per instructions.machine works great!

MAKING NOISE DURING WASH CYCLE

  • Customer: MARK from HEBRON KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 8 of 15 people found this instruction helpful
REMOVED EXCESS WATER,REMOVED HOSES,TIPED BACK WASHER,REMOVED BELT,REMOVED PULLEY AND BEARING.REMOVED 3 SCREWS AND REPLACED WITH 3 LONGER SCREWS IN THE STATOR,THEN REMOVED 3 SHORTER SCREWS.THEN LOOSEN VERY SLOWLY EACH OF LONGER SCREWS TO RELIEVE PRESSURE FROM THE BRAKE SPRING.ONCE LOOSE,PULLED OUT BRAKE ROTOR.REPLACED WITH NEW PARTS.WORKS LIKE NEW.

Water intermittently leaking from bottom of washer

  • Customer: Debbie from Colchester CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers
  • 5 of 6 people found this instruction helpful
I could not tell where the leak was coming from. It was intermittent. Also the clothes were not getting totally dry in the spin cycle. Finally the drum stopped turning. The bearing in the waterpump was shot and the water was leaking from the waterpump. Luckily or unluckily, the bearing completely went and I then found out that the intermittent leaking was coming from the pump. I replaced the pump and the belt that was damaged when the pump bearing locked up. This has resolved the leaking issue.

Topside door would not remain in an open position; lid hinges worn out.

  • Customer: James from Oakland MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
The lid hinges are fastened to the top of the washing machine body, near the edge of the lid, with 1 screw each.
To remove the old lid hinges, with the lid clamped in the open position, I needed to gain access to the screw heads from underneath, just inside the edge of the lid opening. To get at these screw heads, I needed to push the inside wash drum toward the screw I wanted to remove and wedge something in the gap created between the body of the washer opening and the drum, directly opposite the screw that I pushed the drum towards. What? This is to hold the drum completely out of the way while getting at the screw. My wedge was the handle of a squeege that just happenned to be nearby, but just about anything will work.
Once the drum was secure, I was able to get at the screw head, which, by the way, is a totally blind operation; you cannot see the screw head, only feel it. I guess we're kind of used to feeling our way around these days. Anyway, I had to repeat the wedging thing to remove the other lid hinge.
The only real problem I had was the original (factory installed) screw heads were hex heads, and I struggled a bit finding the correct size allen wrench to blindly remove the screws. It is a good thing that I also ordered 2 new screws along with the new lid hinges because the new screws have phillips heads. Much easier to work with, even though they were a little pricey. The old hex head screws were kind of worn and it would have been a cursing operation to try to reuse them.
Once the old hinges were off, I removed the lid, installed the new hinges on the lid and clamped the lid in place in the open position, while I screwed the new hinges on (wedging the drum out of the way like before). NOTE: It might be a good idea to line the wash drum with newspaper in case a screw slips out and finds its way into one the holes in the drum; lost forever. Anyway, this may sound like alot, but it really isn't. My wife didn't even comment on how the lid isn't smashing down on her any more. That's OK, I'm grateful I'm not the one doing laundry!

Grinding noise, then motor shut off.

  • Customer: Joseph from Phoenixville PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 5 of 6 people found this instruction helpful
Disassembly
- Took the back bottom plate off.
- Removed hoses.
- Removed pump with pulley (3 nut screws)
- Removed belt

Installed new parts
- Installed pump with pulley (3 screws)
- Installed belt by placing on 2 small pulleys, then turning onto the large pulley (used a screwdriver to help align over pulley for leverage).
- Replaced hoses
- Replaced back plate.

washer overflowing

  • Customer: Aaron from Lawton OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 9 people found this instruction helpful
Once the washer was unplugged, i removed the two screws on the back pannel, disconnected the three wires, rubber water line, and two screws holding it to the control panel. Quite simply reversed the process with the replacement part i ordered, which arrived overnight, and the problem was solved.

Broken agitator caused intermittent shutoff

  • Customer: Tai from Lenexa KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 6 of 10 people found this instruction helpful
1. Pulled top off (liquid softener dispenser section)
2. Put 2 socket extension and a 13 mm socket together with socket wrench (tool).
3. Insert tool with 13mm socket end into old agitator and unscrew bolt.
4. Remove tool and then remove old agitator.
5. Turn old agitator upside down to remove bolt.
6. Insert new agitator where old agitator was in washer.
7. Insert bolt.
8. Insert tool with 13mm socket end into old agitator and screw in bolt.
9. Pop top back on.

Hardest part was finding extensions because one wouldn't reach.

new belt worn out by a bad motor pulley

  • Customer: ALBERT from WASCO CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 5 of 7 people found this instruction helpful
i took off the old belt and i took off the motor pulley with the pliers and srewdriver. i put the new pulley in with my hand and gave it a hit with the palm until it snap in and then i put the belt on by rotating the main pulley on tub till the belt was pulley on.

Water would not shut off after filling desired level

  • Customer: Richard from Geneva OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 5 of 7 people found this instruction helpful
Took out the two top screws out that hold the top down on the back so you can lift the lid up. Removed the cover plate on the back. Take out the screw that holds the valve in place. Reach up through the access panel and undo the to clips that hold the hose and wiring. Lift the lid up and pull the unit up and remove hose and electrical connections and put back in reverse order. Very simple to do.

Noise during spin cycle

  • Customer: CHERYL from HUDSON NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 5 of 7 people found this instruction helpful
Noise loudest during spin cycle. Wash cycle showed transmission was ok. Pump shaft loose in housing. Fix was just as described. Tip washer up, lift belt from pulley on pump. Remove rear panel access. Remove hoses. Un-bolt pump. New pump does not have metal base plate, it fits directly to base of washer. Bolt new pump to base in same orientation, attach hoses, tip washer up and slide belt back on to pulleys. Move belt by hand to check function. Reconnect washer to utilities and begin fill. Check for leaks at hoses. Replace rear panel cover.

The timer would quit in mid cycle. Spin did not drain the water in Permanent Press or Delicate cycles.

  • Customer: Dale from Benton LA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 5 of 8 people found this instruction helpful
I opened the front of the machine. The clips had rusted. One broke and the others were very difficult to work with. I pried the panel open with a large screwdriver. I took the back panel off to access the water pump. I removed the back panel on the electricals to access the timer. To replace the timer I pried off the decorative cover. To get the knob off you have to squeeze in on the timer split shaft while pulling out on the know. This was the second hardest part. (The front panel access was the most difficult). After that the timer clip is easy to loosen and it slides a littel then pops out. Electrical connection was obvious. The motor sping was the next most difficlt part. The spring fits on the rear part of the motor which is most easily accessed through the rear panel used for replacing the water pump. The water pump has three screws holding it and two hose clamps that come off easily with a pair of pliers. Before removing the water pump, I had to tip up the machine and take the belt off. This was also pretty easy. Put it back together and works great again on all cycles.

original Factory Water Pump Bearing seized up

  • Customer: Bill from Mount Pleasant MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 4 of 5 people found this instruction helpful
Vey Easy to Fix. 1)Turn Water off at the wall. 2)Remove access panel on back of washer. 3) Remove Water pump. It is bolted down to the bottom of the washer by three nut head bolts. when loose the pump can be manipulated and tilted so the belt will have slack and most likely fall right off. Have a bucket ready. Remove water hose from top of pump by sgueaing clam with pliars and sliding clamp up hose. allow to drain in bucket. Lift drain hose out from wall and allow to drain through the pump into bucket. remove hose from pump that goet to drain. Replace pump and reverse steps listed above.

Water wouldn't stop

  • Customer: Steven from Westfield MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
Unplugged washer then took back off control panel. Removed clamp and tube from pressure switch. Pushed in tabs with a screwdriver and lifted top. Removed clamp and broken tube. Put new tube in place and tighten clamp with nutdriver. Closed top and put other end of tube on pressure switch with clamp. Put back on control panel and plugged in. Clamps are to big for application but do work. So far so good!

White fluffy residue appeared under washer. Unbalanced banging during spin cycle

  • Customer: John from Blue Bell PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
Parts needed: Snubber Ring and 6 Springs (don't put the old springs back)
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to remove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.
All Instructions for the CAV2000AWQ
76-90 of 464