Models > CAP2761KQ0

CAP2761KQ0 Whirlpool Washer - Overview

Get Parts and Repair Help for CAP2761KQ0

If you know the washer repair part you need, you can browse the list of all parts on the CAP2761KQ0, or you can search by name or part description. You can also find your part by where it is located on the CAP2761KQ0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for CAP2761KQ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$28.99

Direct Drive Water Pump

It is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one.

Order within the next 7 hrs and your part ships today!
$2.84

Suspension Spring

Sold Individually. Appliance takes 3 of this part.

Order within the next 7 hrs and your part ships today!
$14.05

Water Inlet Valve with Mounting Bracket

This part could have either a blue colored valve body or a green colored valve body. There are two ports for water to enter and this valve is compatible with a half inch ID hose. I...

Order within the next 7 hrs and your part ships today!
$25.55

Clutch Assembly

A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity washers and black spring for compact washers. As per factory, the green spring (1.24") replaces the black spring (1.46").

Order within the next 7 hrs and your part ships today!
$4.54

Agitator Bolt

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

Order within the next 7 hrs and your part ships today!
$3.84

Tub Spring

This part is used to balance the tub during spin cycle. Sold individually. It is recommended that you replace all 3 at the same time.

Order within the next 7 hrs and your part ships today!
$6.70

Tub Wear Pads - Package of 3

This package of pads contains three brown tub wear pads.

Order within the next 7 hrs and your part ships today!
$2.70

Foot, Front - Single

Sold Individually.

Order within the next 7 hrs and your part ships today!
$7.63

Leveling Spring

This spring is used on the leveling components in a washer. Please note, this spring may differ in appearance, but functions the same as original.

Order within the next 7 hrs and your part ships today!
$2.98

Centerpost Gasket

Also known as Main Outer Tub Seal. This part helps to prevent leaking from the bottom of the tub.

Order within the next 7 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water pump leaking when machine used.

  • Customer: Tom from Granby MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 450 of 470 people found this instruction helpful
The hardest part of this job was pulling the machine away from the wall so the hoses could be disconnected and the machine flipped onto it's back. Putting the machine on it's back does two things. It drains the water left in the bottom of the tub so it won't pour out onto the motor when the old pump is removed, and gives the necessary access to the pump. ... read more

spin cycle did not engage

  • Customer: Andrew from SLC UT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 257 of 273 people found this instruction helpful
researched potential causes, found cluch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly, removed agitator from inside the tub as it is connected to the gear shaft, turned washer on it's back for access to motor, unattached the direct drive water pump from the motor drive, unbolted the 3 gearcase... read more

washing machine is slow to fill with cold water

  • Customer: Roy from Nash TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 216 of 233 people found this instruction helpful
My washing machine became slower and slower to fill over the past several months. It also made a loud squeeling noise during fill-up (all this was on the cold water side only). I removed the old water inlet valve and tore it down, expecting to find corrosion or trash that was blocking the valve from opening completely. Turned out to that the rubber diaphr... read more