Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CAE2792KQ0

CAE2792KQ0 Whirlpool Washer - Overview

Get Parts and Repair Help for CAE2792KQ0

If you know the washer repair part you need, you can browse the list of all parts on the CAE2792KQ0, or you can search by name or part description. You can also find your part by where it is located on the CAE2792KQ0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for CAE2792KQ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.80

Agitator Directional Cogs

Agitator directional cogs, otherwise known as dog ears, come in a package of four and are generally found in washers where the motor is connected directly to the washer. The agitat...

$2.92

Suspension Spring

The suspension is meant to support the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down, or perhaps has stretched out and lost its spring, it could cause the load to be off-balance which can cause excessive shaking, moving, noise and possibly leaks. For this repair, you will need a 1/4 nut driver, a putty knife, a flat blade screw driver, and a pair of needle nose pliers. Disconnect the power supply, fill hoses, and drain hose to give you safe and easy access (have a container nearby for water left in drain hose). This item is sold individually.

$28.33

Direct Drive Water Pump

This direct drive water pump, also known as washing machine drain pump or washer drain pump, is manufactured for washing machines that do not have belts. This is a genuine Whirlpoo...

$46.97

Clutch Assembly

A clutch assembly is found in your washing machine and is responsible for spinning the basket during the spin cycle. A worn-down clutch can lead to a slower spin which can lead to the machine not draining properly, leaving your clothes wet after a cycle. If you notice a burning smell, or the machine shaking and moving more than normal, this could indicate the need to replace your clutch. This clutch assembly comes with a brake cam driver, blue springs for large capacity washers, and a black spring for compact washers. As per the factory, the green spring (1.24 inches) replaces the black spring (1.46 inches). This repair requires a half inch 1/16th socket with an extension and a ratchet, a pair of channel lock pliers, a Phillips screwdriver, medium size flat blade, a small flat blade, and a 1/4 inch nut driver.

$31.12

Water Inlet Valve with Mounting Bracket

The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-color...

$3.56

Tub Spring

This tub spring is also known as suspension spring, balance spring, or counterweight spring. It is sold individually. The function of the part is to counterbalance the weight of the motor on the front of the front-load washer so the washer tub sits straight and even during the spin cycle. You may need to replace the spring if tub is sitting tilted forward. A broken spring will result in the tub being off-balance during the spin cycle which can cause further damage to washer parts. It is recommended to check all suspension springs as they often wear at the same rate. Tools needed for repair are a Phillips screw driver, flat blade screw driver, and a pair of pliers.

$4.63

Screw & Washer (5/16-24 x 1)

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

$4.48

Seal, Inner Cap

This is an inner cap seal, but may also be known as an O-ring, and it is a part for your washing machine. Some symptoms replacing this part will fix include: leaking from your appliance, uncontrollable shaking and moving, loud noise, pumps but will not spin, or if your appliance will not agitate. This model is off-black in color and 3 inches in diameter. You will find this part inside the agitator in the middle of your washing machine. It is recommended to wipe down the barrier before putting the new seal on.

$12.16

Tub Wear Pads - Package of 3

This package of pads contains three brown tub wear pads.

$6.88

Leveling Spring

This spring is used on the leveling components in a washer. Please note, this spring may differ in appearance, but functions the same as original.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washer wouldn't agitate

  • Customer: mike from Kent, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 680 of 709 people found this instruction helpful
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing usin... read more

Water pump leaking when machine used.

  • Customer: Tom from Granby, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 532 of 561 people found this instruction helpful
The hardest part of this job was pulling the machine away from the wall so the hoses could be disconnected and the machine flipped onto it's back. Putting the machine on it's back does two things. It drains the water left in the bottom of the tub so it won't pour out onto the motor when the old pump is removed, and gives the necessary access to the pump. ... read more

spin cycle did not engage

  • Customer: Andrew from SLC, UT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 383 of 407 people found this instruction helpful
researched potential causes, found cluch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly, removed agitator from inside the tub as it is connected to the gear shaft, turned washer on it's back for access to motor, unattached the direct drive water pump from the motor drive, unbolted the 3 gearcase... read more