C306 Jenn-Air Cooktop - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Needed to replace the grease filter!
-
Colette from Annapolis, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old yucky filter
Thanks, have been looking for a replacement for this dinosaur filter forever. It is great!
Parts Used:
-
Diane from Flower Mound, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door comes down to fast, Broken Door Assist Spring
Turn off power at breaker
Turn off water supply
Remove 2 screws at baseboard plate
Remove 2 mounting screws attaching machine to floor
Open door, remove 2 mounting screws attaching machine to bottom of counter
Disconnected water line
Carefully pulled machine out about 8 inches to expose broken spring
Attached new spring using directions included with package from PartSelect
Reassembled in reverse order
Check for water leak before attaching baseboard plate
Turn off water supply
Remove 2 screws at baseboard plate
Remove 2 mounting screws attaching machine to floor
Open door, remove 2 mounting screws attaching machine to bottom of counter
Disconnected water line
Carefully pulled machine out about 8 inches to expose broken spring
Attached new spring using directions included with package from PartSelect
Reassembled in reverse order
Check for water leak before attaching baseboard plate
Parts Used:
-
Gary from Erving, MA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable)
2 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front right burner did not turn on
We followed the instructions on the video after receiving our part - they were perfect instructions and led us right through the repair. I have to say it would have been harder to do with one person - but probably doable.
Parts Used:
-
Vanna from St. Johnsbury, VT
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad burnes off on switch
-
Jim from Two Rivers, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken hinge
-
Don from Exchange, WV
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Downdraft switch on the top of the JennAir inkoperative.
I verified that there was current running to the switch.
Ordered a new switch,
Replaced the switch.
Had a little problem getting the oneway washers off the pegs but not much.
Saved the cost of a repair man and felt good about myself!
Ordered a new switch,
Replaced the switch.
Had a little problem getting the oneway washers off the pegs but not much.
Saved the cost of a repair man and felt good about myself!
Parts Used:
-
Daniel from Fort Walton Beach, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
0 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner only operated on high, no medium or low heat.
First I moved the left rear burner to the right front. No change. Then I moved the burner units from left to right, No change. I guessed it was the control switch and ordered from PartSelect. Turnaround time from PartSelect was excellent.
I turned off the powerr to the range. Removed the screws holding on the front panel and then pulled the panel out far enough to see behind it. I located the faulty control switch and then held the new switch, next to it, and turning to proper orientation. I then, one at a time moved the wires to the new switch. After that it was mount the new switch, put the panel back in place and turn on the power.
I turned off the powerr to the range. Removed the screws holding on the front panel and then pulled the panel out far enough to see behind it. I located the faulty control switch and then held the new switch, next to it, and turning to proper orientation. I then, one at a time moved the wires to the new switch. After that it was mount the new switch, put the panel back in place and turn on the power.
Parts Used:
-
Paul from Collegeville, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
0 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The paint had chipped and peeled on the inlet grill
I lifted off the old grill and replaced them with the new ones. My stove top looks great again. If I could find them, I would like to replace the knobs to turn on the gas!
Parts Used:
-
Ann from Irvington, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
a few months ago, my daughter-n-law and I were hitting up tacos on the grill----the grates melted ---I thought I would have to purchase all of the parts even though only the grates were ruined---I am very pleased with my find with you.
just laid them down on top of burner and coals,----easiest installation ever----We are already grilling ----this is just like grilling outside but in AC
Parts Used:
-
Louise from Sherman, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
18 of 323 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Holes in the air filter of our Jenn-Air grill
-
Janice from Ocala, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The burner didn't heat to full temperature.
First turn off the power to the stove/oven. Next I removed the 4 screws located on the bottom surface of the control panel. You need to open the oven door to see/access them. The control panel can then be removed by rotating the bottom outward which allows the flange on the top to disengage. Next remove the two screws that hold the switch to the control panel. Note which wire goes to which spade connector. A quick photo can help. Undo the wires. Remove the old switch. Reinstall the wires. Mount the new switch to the control panel. Mount the control panel back into the stove/oven. Turn on the power and test. The burner now works as new!
Parts Used:
-
Stephen from Grants Pass, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Grease Filter no longer filtered
-
Phyllis from Stamford, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Replacement
This down draft filter was just what I was looking for. The big box stores (Home Depot and Lowe's) do not carry this size filter. Thanks,
Parts Used:
-
Barb from Holladay, UT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Filter was very old and falling apart.
The grease filter was 20+ yrs old and the mesh was falling of the frame. I was very pleased to find this replacement filter (the first filter I received was damaged....placed a call to PartSelect and have a new one the next day). Can't beat service like that!! Thank you, June Patten
Parts Used:
-
June S from San Antonio, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!