Quick Question!

Have you ever purchased from PartSelect.com before?

Models > C301 Maytag > Instructions

C301 Jenn-Air Cooktop - Instructions

All installation instructions for C301 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the C301
61-75 of 127
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The control knobs had been damaged by heat

  • Customer: Jery from Knoxville, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
Easily removed the old knobs and applied the new ones.

Numbers worn on old knobs

  • Customer: Bruce from Boca Raton, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
replaced old worn silver and white control knobs with new black ones.

New Filter & New Knobs

  • Customer: John from Bossier City, LA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Simply replaced these items with no difficulty. John legrand

Old grease filter had hole wore through

  • Customer: Michael from Mountain Iron, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Pulled the old one out & inserted the new one. Less than five minutes.

Worn out stove top

  • Customer: Redona from Roseville, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
We replaced the burner grates, knobs, air filter and burner pan. Looks as good as new!

Elec. stove-top knobs (imprinted with HI to LO numbers 1 to 10)worn to non-readable.

  • Customer: Lenice from Stuart, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Knobs sent fit the shafts, but due to molded internal stop wouldn't seat. Had to drill out the stop, and also file down the shafts a bit for knobs to seat acceptably closer to stove-top.

Burner won't get hot

  • Customer: Robert from Golden, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
It was very simple. detached front switch panel by removing 4 screws inside top of oven door. Removed knob from old switch and removed nut holding switch to panel. Rotated switch panel to expose guts. replaced wires from old switch to new switch, screwed new switch to panel, replaced old knob. idea came from previous story at this website. Works great.

age & solivents melted the on pilot light lens

  • Customer: JAMES from McALESTER, OK
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
removed the wooden cutter block rt side top and the air exst.vent guard lf side then with a phileps driver 2 screws holding the control knob assm.in. both control knob assm.rt&lf come off the same way. just scraped out what that was left of the old lens stuck in new one and reatached light bulb holder. this bulb holder presses on and slides side ways to lock in place. then snaped control knob assm. back in and tighten the 2 screws. replaced vent guard & wooden cutter block. all was done.

cooks "high" on all settings

  • Customer: Robert from Jacksonville, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Turn off the power. Remove 2 screws (in the blower compartment) and lift up the control panel. Release the switch by removing the fastnut. Unplug each wire from the old switch and place it in the cooresponding lug on the new switch. Screw everything back together and cook.

One electric range top burner element quit heating

  • Customer: A E from Houston, TX
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Kill power to range unit at the breaker. Remove 2 screws on back of center control panel. Lift control panel up and toward rear of unit. Unscrew retainer nut which holds switch in the control panel. Carefully note wiring connections, and unplug all 5 wires from switch with pliers. Remove old switch. Reconnect all wires to new switch. Reattach switch to panel with retainer nut. Replace control panel in range with screws. Turn on power.

Filter replacement.

  • Customer: Gerald from Maplefalls, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Remove and replace grease filter.

front burner would only work on high

  • Customer: william from cairo, IL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Installed the part------very easy

knobs sloppy and discolored and filter bent

  • Customer: Robert from Meredith, NH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
This has been a wonderful cooktop and I could only hope todays quality is equally as good but after 25 yrs. I doubt it especially after looking at new dishwashers in the last couple of days. too sad. but these repairs were minor and no trouble. what amazed me most was ordering one afternoon and the parts were here the following day ! great service

Bad switch

  • Customer: Merwyn from Kingsport, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 1 people found this instruction helpful
As stated on order.

My 8 inch stove top element would not heat

  • Customer: clifford from mead, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
I first replaced the element and the receiver. This required splicing lines which was very easy. It still did not heat (even though my element indicator light was on) so I replaced the switch regulator. This took a little time because of the small space on my model. In fact, I had to replace a wire that had shorted by splicing a 3 inch section into it. When that was done, I simply re-connected the 5 wires in the original positions and reattached the cover. It works like a charm and my wife is delighted because we are hosting a family reunion/baby shower tomorrow!
All Instructions for the C301
61-75 of 127