C236-C Jenn-Air Cooktop - Instructions

Really easy ...followed advice posted from others with same problem. Before anything disconnect the power at the breakers and use a voltage detector to verify there is NO POWER!!!! Only need to remove the two phillips screws on the four controller panel, Slide panel away from you to access the controllers. Match wire/connector for connector from the old to new controller. Reassemble, restore power .. Happy wife!!!. She has been on my case to fix this thing for several years.

I removed two screws that held the switch plate together. Then I removed two screws that held the faulty switch to the swtich plate. I then unpluged one wire at a time from the old switch and pluged it into the new switch. Reattached the switch to the switch plate and then reattached the switch plate to the stovetop. Bingo! Everything worked beautifully. It was so easy and I saved ~ $100.00 by doing it myself, as opposed to a quote that I got from a local repairman.

I remove fore screwsfrom the front panel. Then remove two screws to remove the switch and removed the wire plugs then put everything back together again.

replaced stove top switch

Followed instructions, once saw and how to replace and replug wires as the instructions it was easy as per your instructions

Remove cover plate, install new switch, replace cover place. Replace one wire at a time, a pair of needle nose pliers may be helpful. Surprise of this job was that I had a torque screw driver (I think that's what it's called) to remove the switch from the cover plate. These are the screws you'll see after removing the knob. Find that driver before you begin, mine was in the garage and for the life of me, I can't remember why I ever had one in the first place.
Thanks for a great web site!

After reading the other do-it yourselfers I knew it wasn't going to be an easy task. However, when I received my new switch I saw that the hook up and installation would be a snap. My only problem was removal of the old lock washers so I cut them off with my tin snips and once the new switch was attached to the plate I used a socket on the end of a three inch extension. I placed the socket over the new washer and gently tapped on the end of the extention until the washer was seated. It took about two or three taps on each washer and I was finished. Everything went pretty well. Total time to install was about ten minutes.

remove gas valve knobs, removed two screws holding trim plate on lifted plate removed wires replaced switch and reversed the prior moves.

Very easy

old filter fell into from removing and cleaning,
removed cover pulled out filter ,replaced it with new one.

Removed cover, disconnected 2 wires, attempted to remove push nuts with nutdriver, screw driver, and pliers to no avail. Cut off metal bracket with diagonal cutters, then cut off push nuts with diagonal cutters. Push nuts with kit would not fit the threaded posts. Found washers and regular nuts to attach the switch. Replaced the 2 spades on the wires (both were burnt) and shrink wrapped both spades. Pushed on the spades and reattached the cover to the cooktop.

I've ordered parts from you twice now, and both times the service has been absolutely amazing!!!!!

Now, on to how I did this without fire or electrocution:

Turned off breakers.
Grabbed a beer.
Removed two screws holding in plate.
Removed electrical connectors.
Removed two screws holding switch.
Put new switch in place with screws.
Reattached connectors.
Reseated plate & screws.
Turned on power & tested.
Finished beer and felt very manly.

The hardest part was getting the plate to re-seat.

I just lifted out old filter, and put in new one.

This was a no-brainer: old filter out, new filter in. In addition to replacing an old, greasy filter, I found that the exhaust fan now draws cooking fumes much more efficiently. So why did I wait the 6 years since we moved into this house to do this???

Removed old filter, dropped in the new one.
(This really was not a "repair")

Not much to tell about installing a new grill grate.
Partselct.com was very prompt and efficient in sending out the part.