Models > C221 Maytag > Instructions

C221 Jenn-Air Cooktop - Instructions

All installation instructions for C221 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the C221
91-105 of 119
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

burner switch would only stay on hi

  • Customer: David from Willow Grove PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 2 people found this instruction helpful
Replaced the switch.

Wife left burner on

  • Customer: Alan from Alpine CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 2 people found this instruction helpful
Replaced switch.

The stem of one of my burner switches broke off so I had to replace the switch.

  • Customer: John from Fulton NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 2 people found this instruction helpful
Replacing the switch was very easy. First I unplugged the range to be sure there would be no electrical power to the switch. Then I removed four screws to remove the switch cover plate (located above the oven door). I disconnected the wires from the pin connectors on the broken switch, then removed the switch by removing one hex nut. The new switch was installed by reversing the removal procedure. Took about 15 minutes total time.

The paint had chipped and peeled on the inlet grill

  • Customer: Ann from Irvington NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
I lifted off the old grill and replaced them with the new ones. My stove top looks great again. If I could find them, I would like to replace the knobs to turn on the gas!

Old grate were nasty

  • Customer: Greg from Ortonville MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I actually bought these for a friend. He cooks for everyone that shows up. I haven't seen the new grates in action yet. Will have to show up with some meat and test them out.

Holes in the air filter of our Jenn-Air grill

  • Customer: Janice from Ocala FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply pulled the old filter out and put the new filter in.

Surface burner did not heat

  • Customer: james from Santa Claus IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I ordered part one day, recieved part the next day. I installed it the next day. It worked perfect. THANK YOU!

bad infinite burner switch

  • Customer: selvon from Hyde Park MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
unscrew control panel, remove old sw and put in new one. made sure i no mix up the wires. put in grease filter with old grease filter. I did not install the indicator light. More like a 30 yr old electric stove. model numbers are not even registering now. Maytag has parts for it. Have to look around to match up parts. Parts are common so inside the cartridges can be rebuilt with a set of plugs burners and receptacles that match.

Both burners would come on when you turn on the back larg back burner.

  • Customer: Jerry from Tallahassee FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced surface unit infinite switch

Replacement

  • Customer: Barb from Holladay UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This down draft filter was just what I was looking for. The big box stores (Home Depot and Lowe's) do not carry this size filter. Thanks,

Filter was very old and falling apart.

  • Customer: June S from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The grease filter was 20+ yrs old and the mesh was falling of the frame. I was very pleased to find this replacement filter (the first filter I received was damaged....placed a call to PartSelect and have a new one the next day). Can't beat service like that!! Thank you, June Patten

grease filter was disintegrated and burner knobs were illegaible

  • Customer: Jeanne A from Sonoma CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Installed the new filter and replaced the knobs in about a minute. Customer service helped me find the right parts for an over-35-year-old unit and the installation of them was elementary and took probably less than a minute. I am in business again, cooking for my family; and my visiting relatives can cook without guessing the temperature (previous knobs were illegible. Recommend this site without reservation. (Received the parts in about 2 days!). A real treasure of a save!

Could not read numbers on the knobs

  • Customer: Bill from ROCKLEDGE FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply pull off the old ones and replace with the new ones. Problem was finding the correct knobs with the double "s" shaft fitting.The item number indicated by the model number was incorrect. I saw a kit with four knobs on your web site and ordered the kit and not the recommended item. Turned out to be the right move and the knobs fir just fine.

Burner Knobs worn and bent

  • Customer: Linda from Cadiz KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Placed new burner knobs onto cooktop. easy

burners didn't work

  • Customer: Gloria from Nashua NH
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
After a long time being without a working stovetop-an electrician friend said we needed to change a switch-it was ordered and came very quickly and installed-then it was determined that we needed a switch for the other side of the stovetop-I ordered it and got it the next day! It was a joy cooking Thanksgiving dinner on a stove that worked-and I have a new friend that is interested in seeing me on a more regular basis. I know if I needed any kind of parts, I would check with PartSelect first ;)
All Instructions for the C221
91-105 of 119