C206B Jenn-Air Cooktop - Instructions

The hardest part was breaking the caulk seal between the range and the cabinet. An extra set of hands made the job easier, by holding the panel while I connected the switch. The switch was delivered promptly and I am very happy with Parts Select. I found the other repair stories very helpful.

Our stove is from 1978 and was missing all but one drip bowl. I bought all the replacement parts from all the store, (Walmart, Target, Fred Meyer) nothing fit. I finally found this site and they fit perfectly! Thank you. If I have to keep the stove a while longer at least it looks clean and new now, and it still works great!

Very easy repair. Disconnected the old fan switch, replaced with new one...The only problem with the new one is the round nuts that come with the new switch are not big enough to fit around the fixed posts on the stove...The solution...I saved the old ones.....

disassemble housing and remove fan and motor. Reatach fan to new motor, connect wiring, place gasket around motor and reassemble.

Simply removed the old heating element and plug the new element terminals into socket.

The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.

1. Shut the breaker off; Jenn-Air's design will have you working around hot leads if you don't.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.

Removed 2 screws and lifted the control panal. Replaced the switch. Could not use nuts that came with the switch. Had to reuse the oringinals.

Unplugged old burner element, plugged in new element.

No problem, except the holes in the clips to hold the switch in were so small that the clips would not go over the pegs.
The solution - use supper glue.

:-) - Just removed the old one and replace with the new one. Nothing to it. Takes 30 seconds.

If you are buying online, i'm sure you know to remove atleast 2 screws! and fit them back. It’s very easy to fix it. Only thing that took time out of the 15 minutes is to push the metallic push nuts! But it was interesting to do that. Partsselect.com is really a good site

This was so easy. I've looked for years in stores for these pans. I finally tried the Internet, found PartSelects and, holding my breath at what i'd find, voila'...perfect fit, perfect replacements. And it took just a couple days to arrive. I'll definately be back!
/John

Did not need tools for this job. Simply lift burner element and remove old drip pan and put new one in its place. However - the drip pans that were shipped only fit on the left side of the range. The right side, where the grill attachment goes, is so shallow that the drip pans on that side hit the bottom plate beneath the burner element and would not let the element go down far enough to seat properly. I kept the two pans that don't fit for extras, but I still need shallower pans to fit on the right side.

After examining the burner unit I noticed that one of the male contact spades was burned and look deformed. After removing the spade I discovered that it had been originally manufactured incorrectly. I went on line to try and find the part. I found it at this site . I ordered 2 of the spades and replaced the deformed spade and another one that looked like it had gotten a little hot. She tried the unit and it worked perfectly. She had not used that burner unit for a very lengthy time. The investigation of the problem took a little time, but the repair went very fast. Moral is :" If a spade doesn't look right, it probably isn't", but either the individual spade or plug can be replaced. This site is now my "GO TO" place for parts.