Models > C202 Maytag > Instructions

C202 Jenn-Air Cooktop - Instructions

All installation instructions for C202 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the C202
1-15 of 191
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

replaced filter

  • Customer: ELOISE from MILFORD OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 460 of 464 people found this instruction helpful
pulled old one out , cleaned the area & replaced with the new one.

Old grease filter that I actually did not know I had to change

  • Customer: deborah from fort pierce FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 439 of 519 people found this instruction helpful
Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen

Stove top element not working due to bad receptacle.

  • Customer: Richard from Carthage NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 93 of 102 people found this instruction helpful
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.

My Jenn-Air is an "antique." The filter was disgusting!

  • Customer: marion from aspen CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 160 of 305 people found this instruction helpful
I had put up with a filter that got more and more raggedy every year, but I thought my 30 yr. old range/grill top was too old for me to find an replacement filter. What a great service you offer. I found you by web-surfing, typed in the model #, and presto--you sent me the shiny new filter. All I had to do was pop it in and throw away the nasty grill (after washing the scent off to keep the bears out of my Colorado garbage.) Thank you!

Falling apart 20 year old grease filter for downdraft counter rangetop

  • Customer: Roe from Raleigh NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 144 of 286 people found this instruction helpful
Cleaned out the downdraft cove, inserted the new filter, and put old filter in garbage can. Laughing. Thanks. Wish you had a FAQ's hotline. I'd like to know if the radiant inserts fit the older coil-type models.

Burner had no temperature control other that full on.

  • Customer: Eric from North Andover MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 28 of 36 people found this instruction helpful
Locate and open appropriate breaker to kill power to the range. (very important if you intend to see tomorrow).

Pull off the control knob.

Remove 2 screws that hold in control pannel.

Lift out the control pannel to the extent that the wires will let you. (2-3 inches)

Remove the nut that holds the switch/controller in the pannel.

Remove the wires one at a time and reconnect them to the new switch. Make sure to connect them the same way on the new switch.

Re-install the switch in the pannel.

Re-install the pannel in the stove.

Close breaker and test burner contol.

Burner Switch Broke were Knob attached

  • Customer: Malcolm from White House TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 16 of 19 people found this instruction helpful
First I cut off power supply, removed screws that held panel on, pulled the switch up and disconnected wires. Installed new switch, being sure to connect wires in the correct places. Refastened panel to stove top. Turned power back on and tested switch and it Worked.

Wanted to "renew" cook top

  • Customer: Lucille from Mattoon IL
  • Difficulty: Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 17 of 24 people found this instruction helpful
The drip pans, burner knobs and electric surface elements are easily removed and replaced. The new receptacles for the burners were NOT easy to replace, but electricians were on hand to install when they replaced the cook top into the new counter top. Even the electricians had to read the instructions - and remove the control panel to replace one of the receptables. Looks like a new cook top.

Lettering on old stove knobs was no longer visible and knobs were loose.

  • Customer: Chris from Poway CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 15 people found this instruction helpful
Took the old knobs off and replaced them with the new!

blower motor died

  • Customer: Janellen from Aiken SC
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 16 of 30 people found this instruction helpful
Pulled the motor and blower wheel from below. Replaced both. I think it was easier to replace the two together than just the motor.I also had old light indicators so we replaced them since the stove was sort of apart. The repair was not difficult at all, and my 30+ stove top looks and runs great!

burned out heating element

  • Customer: randy from manitou springs CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 10 people found this instruction helpful
part came quickly and fit perfect... everything works great...pretty simple repair... nice to have the right part and have it arrive so quickly

Just ugly this time`

  • Customer: Susan from Chino AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 11 people found this instruction helpful
It's wonderful to get accessories for this 20 year old Jenn-Air. I love it and now it looks like new.

The drip bowls were old and stained; the knobs were so worn that they could hardly be read.

  • Customer: Mary Jo from Minford OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 9 people found this instruction helpful
OK, this was easy, and it's a good thing 'cause I'm so blonde when it comes to repairs. But I will have to say this, my Jenn-Air looks like new and it is 29 years old. Thanks Partselect for making my repairs so quick and easy.

Two heating elements couldn't be controlled - full on

  • Customer: Lansing from Alamo CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 6 of 7 people found this instruction helpful
Turned off power.

Removed two screws to free up section of cooktop containing 4 switches - 2 good, 2 damaged. Removed the dials from top of the 2 damaged switches. With an adjustable wrench, loosed nut on stem of switch that fastened switch to assembly. Noted which of the 5 wires on each switch went on which tab. Pulled off 5 wires on one switch, finished removing the nut and removed broken switch. Put in new switch, attached the nut, and replaced 5 wires in exactly the same position, Tightened nut. Replaced dial. Repeated procedure for second switch. Placed section containing the 4 switches back on cooktop and inserted/tighted 2 screws holding it in place.

Turned on power.

Told cleaning people to NEVER put aluminum foil under the burner units again. The foil shorted across the power and damaged the switches.

Control switch broke off at the knob

  • Customer: Deborah from Newburg MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
My husband actually did the repair and it went very smootly. He removed the palnuts on all switches even though we were only replacing one switch. Then removed the two screws to the switch cover, and slide the cover up to expose the switches. He then took off one wire at a time from the old switch and replaced it one the appropriate place on the new switch. Exteremely easy repair and thank goodness because I (his wife) was the one who broke the switch. Thanks PartSelect!!
All Instructions for the C202
1-15 of 191