Models > BX22S5W (P1196701W W) > Instructions

BX22S5W (P1196701W W) Amana Refrigerator - Instructions

All installation instructions for BX22S5W parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the BX22S5W
256-270 of 325
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The freezer compartment was not cold enough.

  • Customer: Tom from Paducah KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I found the condenser fan was not working so I bought a new condenser fan kit and installed it. Fixed!

Freezer to Warm

  • Customer: efrain from fullerton CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Follow suggested parts to look for. Video very simple to follow repair instructions. Refrigerator back to normal.

Condensor motor was frozen

  • Customer: john from thibodaux LA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
pull unit away from the wall, and unplug it. remove the grill, and cardboard guard on the lower back of the unit. remove Three screws for the motor bracket. Remove the bracket legs from the old motor and assemble them to the new motor. take the fan blade off the old motor, place it on the new. Cut the wires at the old motor, strip the insulation back, use supplied wire nuts to connect the new motor. Reverse order to reassemble. Plug in unit to test function.

Frost buildup in the freezer resulting in warm freezer and refrigerator

  • Customer: Kathryn from Oregon City OR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I unplugged the refrigerator and defrosted the freezer. I removed the plastic grate on the front bottom of the refrigerator and removed the plate covering the defrost timer using a nut driver. I used pliers to unplug the defrost timer. Using the Instant Repairman troubleshooting instructions from partselect.com, I used a multi-tester to determine that the current defrost timer was bad. I ordered a new one from partselect.com and and received it very quickly. I plugged in the new defrost timer and screwed it back in place. I replaced the grate, plugged the refrigerator back in. It's been a week and everything is working perfectly! Easy peasy.

Light bulb failure

  • Customer: Grant from Alexandria VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

compressor will not start - when you turn it on - it hums for a few seconds and them you hear a click sound (the overload opens) and the hum stops

  • Customer: Cliff from Metairie LA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
be sure the power cable is NOT plugged into an electrical outlet - removed the cover on the bottom rear of the refrigerator - using a flat blade screw driver pry the cover off the side of the compressor - remove the old relay - remove the wires from the old relay and install them on the new relay in the same location - install the new relay on the compressor connections - snap the cover back on the compressor - replace the cover - power the refrigerator on - the compressor should start and run normally

Installation of PS2007711 Freezer door gasket

  • Customer: D. Iris from Vestal NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I left two half loose bolts at the top and removed all the rest. The shelf shell remained on while the gasket was worked around and into place. Perhaps it might be a little easier to entirely remove the shell to get the gasket set around and into the groove.

broken handle

  • Customer: Victor from Tulsa OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Put on new handle. thank you for your quick response.

Refrigerator not cooling, bottom freezer was working fine,

  • Customer: Anne from Euclid OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced thermostat and thermostat timer, very easy. Watched instructional video, was very helpful to confirm what I needed to do. Parts snapped right in place, very easy, worked great.

Handle on refrigerator door replacement

  • Customer: John from Cordele GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Quick and easy. 6 screws to unscrew and screw back. Part arrived quickly and was just what I needed.

Crisper drawer support was missing

  • Customer: Ann from Kokomo IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just lifted the drawers slightly and put the support in. Very easy and the part was perfect.

broken roller

  • Customer: mark from marcella AR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
went by instructions, used a little common sence.

The Evap. motor had to much end play and noisy

  • Customer: Larry from Philadelphia PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed all food and basket, took off the panel in the bsck of the freezer removed the motor and bracket and installed new parts.

damaged, freezer door gasket

  • Customer: carlos from cutler bay FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
take out all screws , installed the new gasket,to put back the scews ,used the nutdriver ,verified and that is all.

Light socket not working

  • Customer: Romeo from Edinburg TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Pull out plastic cover #13of refrigerator part discription (temp. control and light socket), snap out old light socket and replaced with new light socket. light is now working.
All Instructions for the BX22S5W
256-270 of 325