Quick Question!

Have you ever purchased from PartSelect.com before?

Models > BWXR473EV0WW

BWXR473EV0WW General Electric Dryer - Overview

Get Parts and Repair Help for BWXR473EV0WW

If you know the dryer repair part you need, you can browse the list of all parts on the BWXR473EV0WW, or you can search by name or part description. You can also find your part by where it is located on the BWXR473EV0WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for BWXR473EV0WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$5.91

Drum Bearing Slide - White

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

$44.28

Front Drum Bearing

Note: The drum slides should also be replaced when your replacing the drum bearing. Slides are NOT included. This part helps your dryer operate as quietly as possible.

$8.55

Duct Felt Seal

May differ in appearance but functions same as original.

$4.11

D-Shaped Knob Insert Clip

Sold individually.

$22.48

Drive Belt

This drive belt is 89.5" long.

$49.31

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running as smoothly as possible with as little noise as possible.

$10.69

Door Handle - White

This part is on the outer door of the dryer.

$37.86

Cycling Thermostat - 4 Wire

This thermostat helps to regulate the dryer's internal temperature. L210-30F

$11.17

Interlock Switch

This part is a simple on/off mechanism that prohibits the appliance from operating when the door is open.

$35.73

Rotary Start Switch

This part is used to start the dryer once you have selected a setting on the timer.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Heater element went out

  • Customer: Brian from Clinton, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 144 of 178 people found this instruction helpful
First of all, unplug the dryer. I removed the two screws on the front of the cabinet to remove the top. I then took out the screws to remove the dial panel. Release the belt for the drum through the access hole in the rear of the dryer. Remove the front cover and pull the drum assembly out.

Remove the element disc from the rear of the housing... read more

original duct was broken

  • Customer: Chad from Gilbert, SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 121 of 138 people found this instruction helpful
Dear PartSelect.com,

My repair went off without a hitch.

2 screws removed to remove top.
4 screws removed from inside to remove front panel w/ door.
4 screws removed from top of control panel, loosed and popped top right off.
Flathead screwdriver to pop off old plastic panel.
Removed old wire chase (plastic, approx 3... read more

Dryer would get very hot and then turn off

  • Customer: David from Auburn, MA
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 241 of 516 people found this instruction helpful
It was actually my father, he doesn't use the internet. He thought that because the dyer got real hot and then shut off he thought the thermostat wasn't working and the high temp shutoff was okay. He went through the manual and found the part and took it out. He called the service number but they wanted $50 dollars plus shipping. I saw it was a Thermo-disc p... read more