BWXR473ET2WW General Electric Dryer - Instructions

Pulled the front of the dyer off, snapped old bearing off, snapped new drum bearing in, affixed 2 new slides and 2 new other widgets (5 pieces total). Vacuumed/cleaned out various bits and pieces before i closed her up.

No squeaking.

Called a priest, but he died. Now i just do whatever the demon says, but i do it with quietly dried clothes.

easy no problem

First I removed the removed the screws that held the top on the dryer. Next I removed the screws that held the controls on from the back. I then removed screws that held the left side in place and removed the drum by first removing the drive belt.
The heating element unit was removed by removing four screws and the wiring harnes. I reversed the procedure to install the heating unit and put the machine back together.

unplugged dryer ,pulled dryer front and top off and removed drum , found element wire broken . loosened element to be able to remove wire pods . reverserd removal ( belt is a little tricky ) reattached power cord to outlet worked like a charm.

Someone I'm related to by marriage accidentally dried a plastic-coated tablecloth on high heat, and our heat deflector was hosed. I was very happy to find this part here for such a reasonable price; Sears wanted about $65 for it. Installation required a Torx bit, and removing the old one was easy, but the dryer's design made it difficult to reinstall the heat deflector while keeping the dryer running concentrically. I ended up cutting the heads off three screws, threading those into the plate behind the drum, sliding the new heat deflector on over those, and then one by one replacing them with the original Torx head screws. Once I figured it out it didn't take long but it took me a while to figure it out. That's probably more a reflection on me than the dryer!

The heating element was broken.

A very easy fix. Opening the front door to the dryer locate two chrome phillips head screws in the upper part of the door opening which hold on the top of the dryer. (I think in the older dryers the top simply was held on with keepers and you could simply pry it off. Not the case here)Lifting up on the front of the top it comes away from the back control panel. I would recommed that the control panel be removed as it is necessary to remove it to put the dryer top back on due to three clips that wont allow you to put the top back down with the control panel in place. It takes a star wrence to remove it. Once the top is off ther are two phillips screws holding the front of the dryer on (one on each side) remove them and the whole fron lifts up and off. The drum rides on a plastic schroud attached to the dryer inside front. Mine was so worn it required the purchase of the entire assembly which comes in two parts. The upper part had worn away so badly the drum was riding on the metal causing the noise. I ordered both the upper and lower assembly and both just simply snap off and the new ones snap right back on. No tools. I was a bit dissapointed as I assumed that the felt which is located in the lower assembly would come with the new part however it did not nor did some plastic tabs which the drum rides on in the upper assembly comes with the replacement part. It takes four of those tabs so order appropriately. Went back together easily and the whole job was done in about 40 minutes.

I removed the screws holding the cover for the switches.I twisted the old timer loose.I moved wires one by one to the new timer with pliers.Lastly, I twisted the new timer to the locking position and replaced the cover.Everything now works fine

Everything is cleaned as it is removed.

Remove the two screws holding the top down.
Disconnect two wires from door switch.
Remove the two hex screws holding the front on.
Remove the 4 screws holding the access panel on the back and disengage idler pulley to loosen the belt.
Remove the drum.
Label the wires then remove the heating element.
Check orientation of ground strap before disassembling rear bearing.
Remove four screws holding rear bearing to back of heating element.
Install rear bearing and ground strap on to heating element.
Reinstall heating element.
Reconnect wires.

Most Important : Get help putting parts back on drum! I didn't and that's why it took over 2 hours.
I will describe how I did it.

Unscrew bearing from inside of drum.
Wrap screwdriver with tape to a little larger than the screw hole.
Use small screwdriver to line up the drum, shim and deflector.
Don't forget the brass shim. It wasn't on the parts diagram.
Start two screws don't tighten them yet.
Remove Screwdriver and start third screw. Tighten all three down.
Put belt on drum.
Install drum and belt.
Reverse disassembly.
When putting the front on make sure drum rests in the felt.

I rated this a bit difficult because I did it myself. With help this is a fairly easy repair.

straightforward swap, just form the top rail and click it in

First, let me say that my repairman said the bearing and slides would cost between $150-200, and the total repair would be pushing $400, so we should just get a new dryer. Well, the total cost for the parts was less than $50.

The installation was easy.
1. Remove the two bottom screws of the door hinges, loosen the two top screws, and remove the door.
2. Unscrew the two screws, under the upper lip of the door opening, that secure the front panel to the top panel.
3. Pull the front of the top panel up, and then pull the panel off.
4. Remove the bulb from the front panel.
5. Unscrew the two screws, from inside the dryer, that secure the front panel to the frame.
6. Pull the front panel away from the drum and frame. Had to lift the drum slightly to do this. The electrical connection wire was still attached to the front panel.
7. Slide off the old drum bearing from the inside of the front panel.
8. Insert 4 new slides onto the new bearing.
9. Slide the new bearing onto the rim of the opening in the front panel.
10. Reset the front panel back into the slots at the bottom front of the frame, with the bearing fitting into the drum. Again, had to lift the drum slightly to do this, and make sure the wire was not caught between the front panel and frame.
11. Re-secured the front panel to the frame with the two screws.
12. Replaced the bulb in the front panel.
13. Replaced the top, and re-secured it with the two screws.
13. Put the door back on.
Quiet dryer once again! And saved the $800, including installation, a new gas dryer would have cost us!

Replaced idler pulley and belt very simple

Having recently replaced the heating elements and main bearing on the dryer I knew how to take the thing apart, getting to the motor was easy. However, the fan side of the shaft was longer than the original so I had to bend out the metal front panel where the fan is located so it would spin without grinding against the front of the dryer. That done, the rest was easy to finish, mounting bolts on the motor tightened, one last test before putting it back together and all was well. The dryer now works better than it has for a long time.

Opened door, removed screw holding down metal plate that presses against interlock switch when door is closed. Removed plastic cover thingy that is over interlock switches. Removed the interlock switch by pressing the plastic lock thingy away from switch. Pulled the wires off each end of the interlock switch. Removed new interlock switch from plastic bag and reversed above procedure. Done, shut door and the dishwasher works.

I've always heard it was a simple job to replace the belt and that would solve the problem. I'd defer to others online when they suggest to replace the rear bearing - they are totally right about that suggestion. My bearing basically fell apart in my hands. Not sure if I needed a belt or not, but it's worth replacing while you are tearing the thing apart. It took way longer to tear apart than to put back together. The parts and prices from PartsSelect were perfect. The parts were received in 4 business days as they said and were perfect replacement parts.