Models > BVLR333ET0WW

BVLR333ET0WW General Electric Dryer - Overview

Get Parts and Repair Help for BVLR333ET0WW

If you know the dryer repair part you need, you can browse the list of all parts on the BVLR333ET0WW, or you can search by name or part description. You can also find your part by where it is located on the BVLR333ET0WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for BVLR333ET0WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.62

D-Shaped Knob Insert Clip

Sold individually.

$46.29

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running as smoothly as possible with as little noise as possible.

$8.52

Drive Belt

This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.

$26.67

Rotary Start Switch

This part is used to start the dryer once you have selected a setting on the timer.

$8.98

HANDLE WHITE

$14.88

Idler Pulley Wheel

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$1.70

Screw

This screw is sold individually.

$33.00

Lint Filter with Frame

This part may differ in appearance, but functions same as original.

$5.73

Drum Slide Bearing

This bearing is sold individually. Some dryers require up to three of these slide bearings. Be sure to check to make sure you order the necessary amount for your dryer.

$2.79

LATCH DOOR

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dryer belt broke

  • Customer: Matt from La Belle MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 90 of 103 people found this instruction helpful
first I took the dryer apart 1st thing i did was unplug the power supply (safety first) then I removed the top of the unit then removed the front cleaned all the lint from the inside of the cabinet I found the proper belt size on part select.com the next day I had my dryer belt delivered (which cost 1/3 the price of the local repair shop price)
then I ... read more

no heat

  • Customer: Joshua from Cardington OH
  • Difficulty: Very Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 79 of 98 people found this instruction helpful
had to remove top of dryer 2 phillops screws at top in the door opening. flip top out of way take 2 screws out of insides that hold the front on. un hook all plugs and remove front of dryer. once u have did this you need to remove the drum by pulling it out of the bearing in the back un hook the belt from the motor and remove the drum this should expose the ... read more

Broken Knob Post

  • Customer: Jaren from Lemoore CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 70 of 85 people found this instruction helpful
First I unplugged the dryer, then I removed the access panel on the back of the control panel. I removed the wires from the back of the switch...Here is where I messed up. I removed the switch prior to ordering the part, the bad part is the way I removed the part. When you get the new part in you will be able to see how it will be mounted to the control pane... read more