BSS25JFTBWW General Electric Refrigerator - Instructions

Could not have made the repair without the On lIne Instructional Installation Video. The video was extremely informative.

Exactly as the instruction video said. I could have done it without the instructions but I would not have cut a piece off the two water lines and possibly had problems down the road. Also, I may not have figured out the easy way to remove the two lines from the valve body. I believe this is my 3rd time using your process and it's absolutely the best. I won't go anyplace else. Next project is probably replacing the ice maker.

Took old auger out then put new one in. Wasn't that bad at all to install.

The repair was very straight forward. However, there's a step that you need to press in two plastic tabs in order to remove an assembly piece. The video on this site demonstrating the entire repair made that step much easier to accomplish, and lowered the risk of breaking some of the plastic pieces. Overall, I'm very happy with how the repair went. This is an easy repair that anyone should be able to accomplish.

We have put up with this noise for several years and finally couldn't take it anymore. After research on the internet and reading about other folks solving the problem by replacing the main board, I ordered the main board and replaced it. That was a week ago. It has been a week blessed with SILENCE from the refrigerator. Hallelujah!!! It was an easy (if expensive) fix and the instructions were spot on. Anyone have a use for a defective main board?

Removed the ice bucket.... 2) Removed the auger from the ice bucket... 3) replace the auger with new auger... 4) installed the auger in the ice bucket... 5) placed the ice bucket back in the freezer.

We watched the video on your web site and was very helpful. We ordered the part from your site was here very quickly. It took us about Fifteen minutes to replace. Saved us alot of money. Thanks so much for all your help.

it was easy the only thing was i had to cut old harness to remove 2 wires that went to coil that had to go back in the new harness other then that a peice of cake.

Everything went really smooth. Just watched the video on the computer. Took it apart and put it back together with no problems at all.

Watched the utube video on repair then followed it during repair. That made it easy

Watched à video provided at your website. Removed te cover then removed 4 screws holding the control panel' snapped out the old flap and inserted the new one.

Noticed the interior wall hot to the touch when opening cooler or freezer door (side by side). pulled lower panel off in rear of unit and noticed fan motor not working. Ordered new fan motor, installed , still did not work. used volt meter to test for power from main control panel to motor. No power present. Ordered main control panel board and installed. Fixed problem. It ran excellant for about an hour and then the control panel shorted out the main control panel and motor that had just been purchased. Both were replaced at no additional charge by Customer Service. Second installation was a success. Sometimes bad things happen to an already bad situation. It's nice to have the understanding, support and service offered by Parts Select. I guess that's why I use them every time there is a problem. G E is easy to repair as long as you use patience and determination.

Followed the instruction in the video and the job was done in 15 min. BE SURE TO DEFROST THE ICE MAKER BEFORE YOU ATTEMPT TO TAKE IT APART. If you don't, there is a chance that the plastic will crack or worse.

I ordered the part and it was replaced. I always worry that I will get the wrong part or it will not fit. The on-line help with the model number gave me the right part, and this was an easy repair. Gusessing that I saved over $100 from needing to call a repair service!

I followed the instructions in your video (pretty cool). I did have problems removing the escutcheon as your video directed. My refrigerator is different. I found three small holes at the bottom of the instrument panel. I used a small Allen (hex) wrench to pop the retaining clips out of the holes and the instrument panel could then be removed. I didn't have to remove the escutcheon at all. Everything else went as your video showed. Ice maker works great now.