All Installation Instructions for General Electric Refrigerator BSS25JFRFWW

GE refer ice and water kept running

I researched the issue on line and replaced the microswitch. I didn't test the part since it was so inexpensive and the whole process only took me about 15 minutes to complete. I didn't know "where" the microswitch was located until I watched your video, a very helpful tool. Thanks PartSelect, the part arrived 3 days after I ordered it.Mike in Spokane, WA

Parts Used:

Micro Switch

Mike from Spokane, WA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

iCE MAKER LEAKING WATER

Followed the video demo and would have been done sooner but for limited work space- narrow freezer compartment and the release tabs on the electrical plug. First home repair that the air was not blue and got done in under time allocated.

Parts Used:

Ice Maker

Roy H from Leesburg, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Thank you for voting!

broken auger blade

being a service tech for 3 apt. complexs & chief engineer for the Hilton ,this was easy. The only thing you have to remember is how the crush ice blades go back in place. use a dig. cam. if you can't remember.All the rest is common sense

Parts Used:

BUCKET AUGER

donald from the villages, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

broken auger

Just watched the repair video...easy!!!

Parts Used:

BUCKET AUGER

Daniel from Deming, NM
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Unit was shutting down the ice & water despencer would quit. in side lights still on compressor off

Replace main control board .Problem solved.

Parts Used:

Main Control Board Assembly

LYNN from FERRIDAY, LA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

frige too cold

changed sensors did not repair problem,replaced damper with mechanical damper fixed problem.

Parts Used:

Temperature Sensor

John from Island Lake, IL
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Ice maker failed. Easy to diagnose cooling coil was very hot

Seemed simple and intuitive B U T the water tube receiver fooled me. Seemed to be on backwards. So, like my wife suggested, I D I D then read the installation instructions. Yeah! It's amazing what you can do when you just RTI. :-0

Parts Used:

Ice Maker

Al from Coto de Caza, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

did not have water

It took me longer to get my tools then fix the problem. Very easy.Thanks Betty

Parts Used:

WATER VALVE WITH GUARD

Betty from Fenton, MO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

The end of the plastic auger had broken off

Watched the video I found at PartSelect when I ordered the part. Let the ice bucket warm to room temp and disassebled as the video suggested and reassembled with the new part. Knew there would be several parts to the ice crusher and important to get back in order because of the video.

Parts Used:

BUCKET AUGER

rod from athens, GA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

drawer slides broken

took olde out simple replacement. didnt need bearing slide already in parts.

Parts Used:

Drawer Slide Rail - Right Side

chris from wartburg, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Door for ice maker sticking and not wanting to shut

Removed front control panel for depensing ice. Removed solenoid and replaced with new. Replaced tention spring for door. Took approx. 20 min. to complete job

Parts Used:

Torsion-Fit Spring

Dispenser Door Solenoid Assembly

Garth from Salinas, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

a piece of the plastic auger broke off

My husband did the repair while I was at work, he said it was a bit difficult. The ice bucket had to be taken apart, but it is working fine now.

Parts Used:

BUCKET AUGER

Vicki from Kahoka, MO
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Wrench (Adjustable)

Was this instruction helpful to you?

Thank you for voting!

freezer cold fridge warm loud squeeling noise

i followed a video that was on your site, the video couldn't have been easier to follow it was step by step and very easy to follow, i replaced the evaporator fan motor and everything is working fine, i did notice that the evaporator coil was frozen pretty bad when i removed the back freezer panel i am going to check it again in a couple of weeks to make sure i don't have a defrosting problem as of now everything is fine i am hoping it was just the bad fan motor causing the coil to freeze up because of no air movement over the coil

Parts Used: