BSS25GFPCCC General Electric Refrigerator - Instructions

The Ice flapper was warped therefore, it was not closing well. Because of this, the ice dispenser got air in it and the ice cubes would deice causing to make a chunk of ice inside.I went on line, order the part ($5.75 + tax= $12.00) checked Part Select video and did it myself. It really is as seen on the video. It took me less than 10 minutes! I saved $200.00

Read about one other person having this problem and it was dead on. Simple job new solenoid keeps water from leaking unless ice machine requires it.

i watched the free video and then made the switch my ice screw had 4 bolts instead of three that was the only difference used the screw driver to loosen the straps on the connection plug and that was it easy as pie in about 30 minutes i heard it drop a load of ice it beats filling ice trays all the time thank you partselect for the free video it was the difference in my sucess

I followed the directional video on "PartSelect" website. The video was very easy to follow and showed exactly how to easily replace the dispenser door solenoid assembly. I knew it was the solonoid assembly because the I could see the plunger that controls the opening/closing motion of the dispenser door sticking inside the old solenoid. The "PartSelect" website is very user friendly and very easy to use. The part ordered, delivered by standard delivery, arrived the day after it was ordered. I only wish all repairs could be as straight forward and easy as this one, thanks to "PartSelect" and some limited mechanical/electrical knowledge on my part. This was absolutely a "do it yourself" repair at a very significant savings over using an appliance repair service.

I followed the Video on your website and that made it so easy and simple to follow. Thank you!

I simply replaced the motherboard which was very simple and straight forward. No I do have an engineering background and understand the importance of RTFM..... That being said I spent more time cleaning the floor under the refer than replacing the MB. Great success and will certainly order again if and when the time calls.

The repair video was great, made the repairs very easy. Once the old main electrical control board was changed out, the unit started to work good. I also vacuumed the back of the unit where dust had built up around critical air flow areas. I am still having trouble with the filtered water not working. I was thinking the trouble might be the water flow check valve. The cubed ice and crushed ice both work great. The freezer is set on 1 and the refrigerator on the 2 setting. I have found where the water spout comes out of the door, if the ice flapper door does not seal properly, the water freezes at the curve of the water spout. I open the freezer door for 10 or so minuets and that's enough to thaw the spout for use. The cost to do the repairs myself was $160. I saved hundreds of dollars. Thanks PartSelect. Dave,

Replaced flapper, which was in surprisingly good condition. Major part of repair was removing a lot of mold incurred from long term seepage of room air into the ice channel. In the process of the repair, I discovered that the solenoid to the right of the flapper was hanging up badly. I removed it and cleaned both the plunger and the interior cone of the solenoid with alcohol. This removed quite a bit of rust and some mold. Reinstalled solenoid, replaced flapper and it works just fine. May need to replace solenoid if problem recurs. Certainly worth $37.00!

I just unscrewed filter and screwed in filter bypass

Not knowing anything about a refrigerator it was hard to find the source of the noise. Once I could isolate it we googled the appliance repair and found the video from Parts Select and the rest was a piece of cake. Saved a service call and bloated parts prices. Thank you Parts Select!!!

Followed instructions from Parts Select Videos about how to replace solenoid & dispense door/flapper. Only a couple of changes from the video with this model: 1) You can remove the control panel by pushing on 2 tabs located under panel and in front of dispense chute with 2 small screwdrivers, and you do not need to remove the black trim around the dispenser. 2) It would be great if each part, especially the solenoid, included replacement screws since mine were corroded and not easily found at the local hardware store. I would definitely pay a couple of $ extra to add screws to the order, or just have them included in the package with the solenoid.

none required

Removed front display and solenoid 3 screws and replace. Clean and install

First replaced the defrost sensor. Same issue. Tested ohms on heat element basically open. Very high resistance Mega Ohms. Ordered new element 21 ohms. Installed 30 minutes. Only needed a Phillips. Set Frig on 5 setting and working well.

removed front assembly as shown in video replaced flapper,recess crank, recess door spring. Selinoid was rusted so bad and could not function. Replaced selinoid and screws, placed a light coating of Vaseline on all metal parts to protect them from moisture. Should be made of aluminium, good to have someone hold a flashlight for you.